Search results for query: *

I repeated the Firmware updrade and it finally installed. The updrade also wipe out my router settings and I re-entered them. I will monitor to see if there is a change.

BEFSR41 VER 2 I downloaded and installed the latest firmware 1.45.6 and it said that the upgrade was successful but the firmware 1.44.2 is still showing under status. Also whenever I am trying to access the internet, the "Dial-up Networking" box keep popping up asking "Would you...

I never hear the post beeps even after i changed the BIOS not to have "silent boot". Some days it boots fine and some other days it does not boot. Also when it boots, many times it does not start the monitor. I will try to replace the power supply.

I am using a static IP adrees and I get frequent timeouts. My Lynksys router is connected to a RCA cable modem. Everything seems to be ok in ipconfig. How do I troubleshoot this issue. My internet provider is Comcast. Primary DNS Suffix . . . . . . . : Node Type . . . . . . . . . . . . ...

This morning, I gor this error message while booting: "CMOS Checksum Bad" Press F1 to enter Set-up, press F9 to reset default values. I pressed F9 and it culd not find the hard drive and the CD-Rom

I reset the BIOS to default settings and the pc still boots to standby mode. I can hear everything going but no boot and the power button remains yellow instead of green.

I have a Gateway and when booting, the pc goes to standby mode and the power button is yellow. The CD-Rom works and you can hear the fan going but the monitor does not get activated. I replaced the battery. I disabled the standby mode in the power settings and i checked all connections. Once in...

I meants to say that when the power button is yellow, the cd rom works but the pc does not boot

I ha ve a Gateway PC that boots up but the power button is yellow. I changed the battery. At times it boots properly and the power button turns green. In the power settings, i disabled the standby mode. What else can cause the power button to staty yellow? I poened the case and checked all the...

I am formatting a hard drive for NTFS using the win2d CD and the process freezes at 55%. I turned off the pc and restarted the process and the formatting freezes again at 55%. Is the hard drive bad? Can I repair it? It is a Gateway pc.

I should I confugure the Static IP setting for a second pc connected to my Lynksis router. Both pc's are running win2k. Here are the static IP settings for the main pc: Primary DNS Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Broadcast IP Routing Enabled. . . . . . . . : No...

I am using an RCA cable modem, model# DCM305R. Comcast did not want to help me since they do not want customers to use routers. Comcast does not like Static IP address. They prefer DHCP. How do I get my pc's physical adress. It is the same as the MAC adress? Should I use the MAC adress of the...

I am baffled also. I've tried everything and still unable to use DHCP.

I applied the WinsockFix and I rebooted. My IP settings are still the same. Primary DNS Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Broadcast IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Local Area Connection...

I currently access the internet via a static Ip adress. The Link lights on the router and on the cable modem are on. A Linksys tech assisted me with setting up the static IP setup because Comcast did not want to help. I entered The Gateway, the DNS and the IP adress manually. Here is my current...

I tried it but it still does not work. When I edited the registry, under "telephony", i could not find the string cards/next.

My ISP is Comcast and I get internet access via cable modem and a Linksys 4-port Router BEFSR41. With or without the router I cannot get an IP adress with DHCP enabled. I am trying to get internet access throuhg the cable modem alone. Node Type . . . . . . . . . . . . : Broadcast IP Routing...

I am running Win2k and I am trying to set-up a VPN connection. In the "Network Connection Wizard", I only get 2 choices: 1-Dial-up to the internet 2- Accept incoming connections All the other options are grayed out. I need to get access to "Connect to a Private Network through...