Search results for query: *

I have a point to point T1 coonecting a remote site back to the switch. (Opt 81C) They use I2004 phones at that site and are connected via a 2600 and a 3550 (Cisco) to the T1. We have VGW's built and utilize Media Gateway Cards (32 port) without an actual Sig Srv (so I guess you would say we...

It may be too late for an answer, but if you log into your CallPilot Manager GUI and on the home page select the help link, then under Administration Guides it is the first link "Administrators Guide" and it's under configuring CallPilot services.

CallPilot Release 4.0 Document Number: 555-7101-202 (this is the Nortel manual, and I searched ports) TCP port 20 (FTP) TCP port 21 (FTP) TCP port 135 (DCOM) UDP port 135 (DCOM) TCP port 143 (IMAP) TCP port 389 (LDAP) TCP port 636 (LDAP) TCP port 993 (IMAP) TCP ports 1024 to 65535...

Assuming you have everything configured, plugged-in etc. Enable the loop, status the loop (I do anyway), you will probably get this error "DCH1010" D-channel is disabled. LD 60 ENLL loop STAT loop Then enable D-ch should get DCH EST Time and Date, if after you status the DCH again and you get...

LD 60 stat xx (loop number) enter

Preliminary results look promising I will do more testing and post results. Thanx for you help pronei.

Just got back to working this issue. Was able to do the above command per your suggestion. Now just making so calls and I'll see if it worked. I'll let you know.

Alright pronei I was able to change Customize to #1 When I type "Set" (Option) then start typing NLN, like you said the auto fill starts and I get Name (value) and this prompt populates the site name (I am sure you know this) Am I trying to change this Option Settings: HEL to NLN or do you...

Ident MDR-2000 Plus M1 Nortel Generic Rev. 3.S37.G40 Ser. N12406 Copyright (c) 1998 MDR Telemanagement Ltd. M2K> Customize (Enter) (RET - Leave entry unchanged, TAB - Remove entry, Ctrl-C - Exit command) Choices Are: #1 --> 10,18,0,26,32,41,20,3,47,53,53,53,0,0,3,0,7,0 #2 -->...

Finally got it. Date/Time (mm/dd hh:mm): 48/00 00:34 Option Settings: HEL Number of Records Stored: 000577 Records to be Collected: 000577 Port Config (PBX/Modem): 9600-8-N/ 9600-8-N Minimum Duration: 0 Incoming Calls: Yes...

Sorry, for the late response pronei FCDR old As far as MDR box, it's been set up for quite awhile (pre-my arrival) and I have no clue. No idea how to access it (actually I read the OTM stuff) but I am not very savvy with hyper-termminal or those types of Apps to access the MDR, any starting...

Read the post from John/BSLD and ACE on the MDR 2000 and CLID retrieval from Jan/08 and I have a question. Below is the mdr2000.col script portion w/CLID from my script on OTM ; Retrieve the Calling Line ID from the call. let CheckPos = pos('D', M2KData$, FALSE) if CheckPos <> 0 then...

Read the post from John/BSLD and ACE on the MDR 200 and CLID retrieval. Below is the mdr2000.col script portion w/CLID ; Retrieve the Calling Line ID from the call. let CheckPos = pos('D', M2KData$, FALSE) if CheckPos <> 0 then begin loop let M2KTemp$ =...

Sorry if I mis-spoke allenmac, I was trying to say that having only RCAP=COLP on the DCH, that calls then started working again. If I have COLP and NDS I get fast busy on the outbound calls. Thanx you 2 for the info

I have searched the forums and gathered quite a bit of info, and still no luck. When I make all the recommended changes (specifically when I add NDS) then do a FDL on the MSDL ckt comes back IDLE, incoming calls work (no name display, but I'll cross that bridge after this issue) But what I...

Thank you so much. Worked like a champ. I was put 2x 50x and various other combos, but did not try x2 or x50 DUH!!!

Succession 3.0 on an 81C Loop has Pri Dch, BUdch and 2 other T1's (loops 2 and 50) for a total of 4. Int ID 0 and 1 for pri and back-up Dch's Int ID 2 and 3 for the other 2 T's (loops 2 and 50) I have disabled DCH and BUDch in ld 96 I have disabled loop in ld 60 (Loops 2 and 50 also)...

ACE all I know is what it does. I am assuming that w/in the CENTREX switch AT&T has some config that allows it. On our PBX we only provide the CENTREX w/a path to the phones. All the hunting/config's etc. are all done on the LEC side. I of course control what key to put the numbers on ETC...

ACE and GHT I know posting questions and having a "knuclehead" like me not explain in detail is a pain, but I was hoping by saying all is working (in test situation w/4 line HG) and getting the 5th call to VM that it would help eliminate a long and drawn out post :( Anyhow they don't want ACD...

This is what I want to accomplish. I have to program a State Police dispatch center, I have an 81C w/3.0 I already have a small HG built (4 lines w/o using an ACD I just have all the ext MARPed on one phone and it works fine as is. The 5th call I can make go to VM, not sure on any more calls...