Search results for query: *

If you want 1000->100 or 1000->10 to work fine with large TCP window sizes, you will need to make a couple of adjustments. After updating to 4.0, and doing a default on the switches with the new code, do the following. -Go in to the command line interface -Type the following: config t qos...

The Recipient Update service is responsible for creating email address from your policy template. We see that sometime this can get a little flaky, but a right click -> rebuild usually fixes everything. If anyone has a more permanant fix or explanation then I'm all ears.

The only problem with that approach is that the same thing will happen with User mailboxes. Use ExMerge to delete the corrupt message. You can target specific mailboxes and even message subject lines.

You have to be in Native Mode as well

Yes, thats the way it is for changes normally for us as well. However on the duplex settin gi actually get a timeout error immediately

it would be on the 1200 since thats where the ports are coming online. If you are using Device manager, click on the port go to STG tab and set FastStart to TRUE.

I know its not a problem writing to the flash. I can save any other setting. At least any i've had a reason to try. I'm not sure im using the latest device manager. I will check that and post my results. But is there no way to set port duplex setting in the command line Thanks Shawn

Have you turned on fast discovery for Spanning tree. I had a problem on a passport 8100 with that exact problem. The inital discovery process took too long and DHCP would time out.

Sounds like you need a different cable. Some used null modem and some used straight through. I believe the older switches like the 350 used null modem.

I am getting a lot of CRC errors on my 8100 Switch ports. I attribute this to Duplexing problems as every port is set to auto on the swtich and in most (i was working on making it all) the NIC. Anyway, I tried to hard set the both the switch and NIC to 100/Full. When i try to set it in device...

Weird Question. I set up a Media Pool with 2 single drives, and it was working beautifully. Then we had a few bad tapes spring up in the rotation so i replaced with all new Dell DLT IV 40/80 tapes. Now suddenly, after the first tape is full, the job just sits waiting. When i come in in the...

This turned out to be caused by FastEnable being disabled for Spanning Tree Protocol on our network switches

My org is comprised a root domain with subdomains for each branch, we'll call it Company.Com. i am a domain admin of a subdomain branch.company.com. When i netboot i login to the Client wizard with my username, password and branch.company.com is all ready listed. I then get an error that states...

I have an 8100 with redundant 8190SM management modules that have lost their IP connections somehow. The slot 5 MM has apparently been reconfigured from default Console settings (its not 9600, 8-n-1). I am able to get into the redundant with a console connection. Im trying to get into the master...

Well 2000 can plug and play my NIC, it just doesnt have the driver for a boot disk. Regardless, This is never getting into RIS, its just hanging on dhcp address at the very beginning of the process.

This is a PXE install. No, the NIC on the Dells (the PCs we are using RIS to deploy) use a Intel Gigabit Ethernet card that is not supported by the floppy.

Ok, I'm about to pull my hair out on this one if anyone has any new ideas or old ones I haven't tried. -I installed RIS on one of my DCs. -Ran RISetup -AD is set to respond to all client requests. -I have authorized the RIS server in DHCP, and can see the 1045 event message that verifies...

I am a server guy who's recently inherited control of a Passport 1200 switch and an 8100. It seems that during business hours, when the main load is on the network, the switches reset about every 60-90 minutes, causing users to drop for about 3 seconds and each switch throws a coldStart trap...