Search results for query: *

Yes, I would like to see about setting the residents phones to ring the nursing station extension, instead of the emergency call center. If you have any ideas, I would appreciate this. I will not be able to review until March 21st. Thanks

I have contacted our local carrier (Verizon) and they said that our facility was not listed. They made a change request to their database and it should be correct after 7PM. Thank you all for your help. You saved me. This is a very good site. I've used it a couple of times and will probably...

That worked like a champ - Thank You The only thing missing now is the Building ID/Caller ID. The call center indicated that all they had was the number and they should see more. She said I should call our carrier. Does this sound correct? Thank You again for your help.

Sorry about hiding the TNS. Here is the route for the copper trunks: TN 002 0 00 00 MBER 1 TN 001 0 00 01 MBER 2 TN 002 0 00 02 MBER 3 TN 003 0 00 03 MBER 4

I'm told that the system was set up to place all calls, local, regaional, and LD through the PRI first. The trunks are in place as a failover. The part that I'm confused about is how it used to work until a couple of months ago. Like I said in my original post. The 180 beds are all analog...

Stat Results for the Trunk Card: STAT 2 00 = UNIT 00 = IDLE (TRK)(CO GRD) 01 = UNIT 01 = IDLE (RVSD) (TRK)(CO GRD) 02 = UNIT 02 = IDLE (RVSD) (TRK)(CO GRD) 03 = UNIT 03 = IDLE (RVSD) (TRK)(CO GRD) 04 = UNIT 04 = IDLE (RVSD) (TRK)(CO GRD) 05 = UNIT 05 = IDLE...

Which card would it be for the XUT card. I have about 12 or 14 Analog cards, and each of them when I stat them will show all the stations as to being busy or idle. 03 = unit 03 = idle (l500) 03 = unit 04 = busy (l500) 03 = unit 05 = busy (l500) 03 = unit 06 = idle (l500) 03 = unit 07 = idle...

The information on the version and release of the phone was taken directly from LD 22 in the switch - below is the exact printout: Version 2111 RELEASE 22 ISSUE 16 + This facility is located in Franklin Park, New Jersey. Route 0 TYPE TLS TKTP COT ROUT 0 DES COPPER TN XXX X XX XX...

LD 86 RLI 0 ENTR 0 LTER NO ROUT 0 TOD 0 ON 1 ON 2 ON 3 ON 4 ON 5 ON 6 ON 7 ON CNV NO EXP NO FRL 1 DMI 0 FCI 0 FSNI 0 CBQ NO ISET 0 MFRL 0

We are running an Option 11C Version 2111 Release 11 Issue 16 + in a Long Term Care facility. Our switch used to be set up so that if an analog phone (resident) placed a call to 911 it would rings the nursing station. The nurse on duty would determine the validity of the call and place 911...

After doing my loopback test, I discovered that I needed to change out my cable, once I did, then the circuit came up and I got exactly what "johnpoole" stated I would see, the card come up and the D channel show wrong mode. This is what I have going on (I did a Stat of my D channel in LD 96...

This is the status of both my DCH and MSDL: .stat msdl 10 MSDL 10: ENBL DCH 10 DCH000 .stat dch 10 DCH 10 : OPER RLS AUTO DES : INTERNAL .

Below is what I get when I do a "Perform remote loop back test on loop". Is this what you wanted to know. I can not find the Errcode:030 anywhere. .rmst 5 SLFT FAILED DTI009 5 ERRCODE: 030

What's the command to "loop the circuit back to itself"?

Yes, 24 is a D channel.

OK, changing the "DTRK" to YES worked and it allowed me to create my trunk members. Now in LD 60 I can not seem to get rid of the red alarm. A test of the hardware comes back OK. The test of my loop comes back with a: DTI009 5 Errorcode: 030 I can not find an errorcode 030. The codes list...

I can not add my trunk members in LD 14, I keep receiving: SCH2034 A digital route is required. This is what I have built: RDB TYPE RDB CUST 00 DMOD ROUT 3 DES INTERNAL TKTP TIE ESN NO CNVT NO SAT NO RCLS EXT DTRK NO ISDN NO PTYP ATT AUTO NO DNIS NO ICOG IAO SRCH LIN...

I did not have it built that way. I went back and made those changes. Now when I try to add the route members I receive the following error: SCH4788 PRI loop is not configured with D channel (DCHI) to provide B-channels.

I have the loop created in LD 17. I have the RDB built in LD 16. I can not seem to add the route members in LD 14. I keep receiving the following error: SCH2034 A digital route is required. Help

The 1st PRI is connected to the Telco. The 2nd PRI is strictly for 4 digit dialing between sites via the Siemens RG8702 Gateway. Would I add the 2nd card to the original loop?