Configure 2nd PRI for Dialing between Sites

[MorpheusWin2K]

We have 7 locations throughout the state. Six of these locations are on a Siemen's HiPath 8000 switch and the lone remaining location is a Nortel Option 11C. I am trying to configure a 2nd PRI Card for 4 digit dialing between sites going through a Siemen's RG8702 Gateway.

My problem is that I can not get the 2nd PRI Card to go green. I've configured a "Loop" and set up the Trunks/Routes. I can not seem to get the Clock Controller to go green or get a green status. I am told by Siemen's that there end is complete.

Any help in getting this programmed correctly would be appreciated.

Thank You

 

[MorpheusWin2K]

What's the command to "loop the circuit back to itself"?

 

[MorpheusWin2K]

Below is what I get when I do a "Perform remote loop back test on loop". Is this what you wanted to know. I can not find the Errcode:030 anywhere.


.rmst 5


SLFT FAILED
DTI009 5 ERRCODE: 030

 

[Reusser]

Red alarm is a physical layer alarm - no physical connectivity to other PBX.
This could be for a couple reasons:
Other side is not turned up
cable is not connected
Rvc no going to transmit and transmit not going to receive

The loop back spoke of earlier would be a physical connecter with transmit going to recieve

on a RJ48 plug - 1 to 4 and 2 to 5
on a DB15 hood - 11 to 9 and 3 to 1

 

[Triton101]

PRI card NTAK09 will have a DCH daughter-board (user installed) and the DIP switch on the main card will need to be set also. verify if the MSDL is showing up and enabled.
(ld 48 or 96 stat msdl)

From the programming that you have pasted it looks like at NTAK09 DTI/PRI card.

__________________________________________________________
Find a job you love and you'll never work a day in your life. - Confucius

 

[MorpheusWin2K]

This is the status of both my DCH and MSDL:

.stat msdl 10

MSDL 10: ENBL
DCH 10

DCH000
.stat dch 10

DCH 10 : OPER RLS AUTO
DES : INTERNAL
.

 

[bhassell2000]

you will need a looping plug to loop the circuit

Thanks,

Buddy

Linked in Profile

http://www.linkedin.com/pub/buddy-hassell/7/5a5/b8b

 

[bhassell2000]

do you have the circuit wired youtr transit to the far end receive and your receive to the far end transmnit?

Thanks,

Buddy

Linked in Profile

http://www.linkedin.com/pub/buddy-hassell/7/5a5/b8b

 

[johnpoole]

ALARM STATUS : RED

layer one is open.. nothing helps untill that changes..

db 9... pins

1 - 9
3 - 11

that will make it stand up,, go yellow then green.. enll x will bring it up then rls wronge mode.. once that is done at both ends.. connect the ckt back up.. if that goes red.. on ONE end move pins swap pins 1 and 3 with 9 and 11..


john poole
bellsouth business
columbia,sc

 

[MorpheusWin2K]

After doing my loopback test, I discovered that I needed to change out my cable, once I did, then the circuit came up and I got exactly what "johnpoole" stated I would see, the card come up and the D channel show wrong mode. This is what I have going on (I did a Stat of my D channel in LD 96, because it didn't show it up in LD 60 when I enabled the Loop):

ld 60

DTI000
.disl 5


OK
.stat 5


PRI* TRK LOOP 5 - DSBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
.enll 5



OK
.

stat 5


PRI* TRK LOOP 5 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: NO
ALARM STATUS : NO ALARM
CH 01 - IDLE TIE VOD CH 02 - IDLE TIE VOD
CH 03 - IDLE TIE VOD CH 04 - IDLE TIE VOD
CH 05 - IDLE TIE VOD CH 06 - IDLE TIE VOD
CH 07 - UNEQ CH 08 - UNEQ
CH 09 - UNEQ CH 10 - UNEQ
CH 11 - UNEQ CH 12 - UNEQ
CH 13 - UNEQ CH 14 - UNEQ
CH 15 - UNEQ CH 16 - UNEQ
CH 17 - UNEQ CH 18 - UNEQ
CH 19 - UNEQ CH 20 - UNEQ
CH 21 - UNEQ CH 22 - UNEQ
CH 23 - UNEQ CH 24 - DCH 10
.**
OVL000
>ld 96

DCH000
.stat dch 10

DCH 10 : OPER RLS AUTO
DES : INTERNAL