Search results for query: *

I mean if we disconnect Eth0 of one of the LIM then reconnect it again, we face a starnge behaviour, system will hang then works again!!!

Is this a normal behaviour in TSE?

Would like to know if it is possible in TSW to prevent a certain digital extension from detecting the incoming external number? I tired KSCAC/ ADC/ D4=1,D3=0.D12=2 but no success. For some reasons the customer wants the extension to see "External" or "private" instead of the incoming number.

I have 10 LIMs system (TSE 3.2 SP3). some times lim 10 goes out of order due to network a prolem. the main problem is when LIM 10 tries to be back in service the ODD LIMs goes down. The ODD LIMs return back in service with out any action from our side. Is this a normal behaviour? Did any one...

Any adivice...the system is BC12. lets say that the MD110 doesnt request the ANI while we have configured ADC/KSCAC correectly, then what shall we do?

Whorsedaddy, I got confused!! I am setting ADC/KSCAC to 00100000010000. D3=1 (Request A-number from PSTN is not restricted for extension). why should it be Zero.(Restricted for extension)!!. Thanx

Daddy, I just configured ROCAI,RODAI,RODDI,ROEQI. I receive 4 digits from the PSTN, which the same as the extension numbers,and this works fine. I didn't configure "RONDI", should I do?? I just receive "external" on the dispaly. Cfrei, Extension 2440 was called then what is your advice?

Yes, this is checked. can some one help in the traces??

I set up a CAS R2 route with the parameters below:(TSWSP6) ROCAI:ROU=6,SEL=0130000000000010,SIG=311110000050,TRAF=01151515,TRM=4,SERV=2100000011,DIST=30,DISL=128,NODG=0,BCAP=111100; rodai:rou=6,type=tl30,varc=00000000,vari=00002222,varo=00000556; KSCAC:DIR=450,ADC=00100000010000; The route...

I swapped to the new MUXs. but as you said in theory its stright forward but on real it is not. I had some issues with remote LIMs but at the end every thing works fine. Thnx

Hi Guys, I have a critical site in an airport with 12 LIMs-TSW. 6 LIMs are connected to the group switch in the same room. The other LIMs are remote. the remote LIMs are connected to the group switch through the BIM transmission module. the customer wants to replace the BIM by a new...

Thanks for the reply but I want the common diversion position to be voice mail hunt group, can you help??

Hi, I'm Trying CDCOI :INTDIV=0; (0-operator) to divert internal calls to the the operator??!! where I have the CDIV = 001151222; the calls never diverted to the operator or even to a hunt group!! when I try CDINI with modified CDIV it works fine..!! I'm trying for Digital and analogue sets...

I just created a SPEXI between a digital Extension and Analogue runk. The Extension has a limited access (calls locally. after making the SPEXI between the extension and the trunk access code, the extnsion has the ability to call locally, nationally, internationally!!! In other the SPEXI between...

Any news?

System release TSW SP03

Hi, As I know that the Operator can't use central authorization code. The strane is that I have in the Call logging, some calls made by the operator shows that these calls made using Central authorization code. did any one experience that??!! The row data at the hyper terminal looks like below...

The signalling standard is ESPA 4.4.3 standard. Signalling protocol: Speech

where are you experts?

I want to interconnect the TSW with a paging system through TLU80. It's clear in ALEX that it is not permitted to mix external lines with paging on the same board. I executed the procedure below: PAGII:DIR=400,MSAR=2,SCD=2,SSAR=0,PCAT=100...