Search results for query: *

Is it possible to "initiate" the connection from a Cisco 3000 series concentrator to a 3002 hardware client? I have this setup (3000 at central office, 3002 at remote location) about to go into production. It seems to work fine during testing but the 3002 always initiates the connection. Is...

I cannot seem to save the User Password under Systems, Tunnel Protocols, IPSec - User Password. It saves, but when you power off the Cisco VPN 3002 Harware Client, it loses the User Password.

OK...I went ahead and nabbed the routes today :-) LAN a = Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.201 10 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.200...

I will get those routes to you tomorrow... Pinging yields request timed out from both sides and a tracert doesn't give any info past the default gateway which is the lan addy of the 2k3 server... Also...for future ref: lan a = 192.168.1.0 255.255.255.0 server a = 192.168.1.200 lan b =...

I have two 2003 servers connected via routing and remote access across the net. From either server I can get to anything on the opposite network no problem...but when a workstation on one of the LANs tries to hit an IP from the other LAN it does not work. Both servers are set as LAN and demand...

After looking into the IIS logs for my logging needs...I noted all of the connections that do have the domain\username lines say they are to and from 127.0.0.1 with no mention of the internet IP addy? Any ideas as to why this is?

I just installed CSG2 on a test box and it is doing the same thing as our older CSG install (that looks identical in every way...did they just change the name and not the product?) Basically when I look in the event viewer to see who has logged on many of the entries omit the username: Event...

I just tried 0x10f with the boot system flash command (I have been using that syntax)and still nothing... Also note: I have an identical 4003 running the same version software and it works with the boot system flash command and config-register 0x102...which I just tried on this one. It...

Setting the boot statement and setting to 0xf or 0x2 both result in the same thing...rommon upon power cycle :-(

It was set to 0x2 originally...and I do have a boot statement...but I am not totally sure I had both at the same time...I can try that :-) Thanks

I have a 4003 with a sup1 engine running bootstrap 5.4(1)with 5.5(1) software. When you power the switch up it goes into rommon mode...but issuing the "boot" command boots it up just fine. I can then set the boot register to 0x2102 and then issue the reset command and it autoboots fine...

Look at this product: http://www.centuriontech.com/ We used these at a college I used to work and really liked them. They are not exactly what you are asking about but might be part of an overall solution. You might also consider shifting all your student PCs over to a seperate vlan and...

I work for a company that specializes in security and we support several healthcare facilities. Unfortunately the story you told is not uncommon. Usually the folks responsible for IT are overworked and can barely keep things running much less focus on securing the network even if they do have...

I work for a company that specializes in security and we support several healthcare facilities so we are somewhat familiar with this scenario. The facet that hasn't been mentioned yet is probably your biggest threat...internal based attacks. Think about it: Most folks spend what...

I am looking for a DOS command line encryption utility if such a beast exists. I have some hard drives that are headed out and I want to encrypt the data on them before wiping them and since there are several to do I would love to create a boot disk with batch files that boot, encrypt, and wipe...

I am responsible for several 2000 domains with a handful of Exchange 2000 servers each (all win2ksp4 with exchange sp3). On every one when I try to setup the monitoring of smtp queues in the tools/monitoring and status it eternally shows the queue as growing :-( When I searched I found 3 other...

Citrix Secure Gateway is designed just for that scenario. We have it installed at several client locations and it works great. Coty

I am trying to create remote shares on Win2k using the rmtshare command. I have done this a million times back in the NT days no problem. Now for some reason it is giving me Command Failed Error 998 which I cannot find on the net to save my butt. rmtshare \\servername\username=d:\usr\folder...

Figured it out: "no fixup protocol smtp 25" in the PIX firewall... SMTP authentication will not work if the fixup protocol smtp 25 line is in there :-(

Figured it out: "no fixup protocol smtp 25" in the PIX firewall... SMTP authentication will not work if the fixup protocol smtp 25 line is in there :-( Coty