Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. 3cross

    Call Pilot

    Is Auto attendant standard on Call Pilot?
  2. 3cross

    Call Pilot

    I realy cant remember if Auto Attendant is a standard package on Call Pilot?
  3. 3cross

    Counting # of calls to outside number w/o cdr?

    Is it possible to count the number of times a specific number is called w/o using cdr?
  4. 3cross

    Visual indicator light from incalls on 2216 set?

    Is there a way to light a indicator light on calls to an incalls key on a 2216?
  5. 3cross

    Why won't CLID info transfer?

    We had a problem where then CLID would not pass until the call was answered and the problem ended up being a patch on the SS that wasn't suppose to be there.
  6. 3cross

    Why won't CLID info transfer?

    Was this ever resolved? If so what was the resolution?
  7. 3cross

    PC program doesn't work through ethernet port on set

    I should add that the program runs but it seems to loose packets or not run fast enough or something so that it fails to run properly.
  8. 3cross

    PC program doesn't work through ethernet port on set

    Users use a program that won't run on there PC through the ethernet port on the set but if they bypass the phone and use the same switch port directly it runs fine. BCM 50 / 1140, 1210 and 1230 sets / problem software is Nova - Day One / using voice and data VLANs /
  9. 3cross

    How do I send number besides DN over tie

    I read the downloaded info and followed the first example. This was routing the calls out over a branch using NRS and in the SPN I needed to set CLTP to NATL. It was at none and the calls were treated as UDP or CDP calls and always used the ext. #. Using element manager for making changes to...
  10. 3cross

    How do I send number besides DN over tie

    I can't get the CLID table to send a specific #. I can get it to add the area and office code I need but it always uses the phone DN. These are going over a tie then out a PRI at the other location.We are trying to use ext. 6133 on the outbound ID instead of the DN. Everything works but we can't...
  11. 3cross

    Cisco DID PRI tandem through OPT 81 DID PRI

    The 9 is coming from the Cisco and all works well now that it is built as a tie. When it was a DID it would not look at more than 4 digits because of the LDN0.
  12. 3cross

    Cisco DID PRI tandem through OPT 81 DID PRI

    We changed the rt. from the Cisco to a tie rt. and it works.
  13. 3cross

    Cisco DID PRI tandem through OPT 81 DID PRI

    Since the inbound calls from the Cisco are on a DID will the opt 81 look at more digits then what is defined by LDN0? Will it even look at the whole digit string to pass it on out the outbound circuit?
  14. 3cross

    Cisco DID PRI tandem through OPT 81 DID PRI

    Below is the route and trunk info. Cisco rt TYPE RDB CUST 00 ROUT 20 DES Cisco TKTP DID NPID_TBL_NUM 0 SAT NO RCLS EXT DTRK YES DGTP PRI ISDN YES MODE PRA IFC S100 SBN NO PNI 00000 NCNA YES NCRD YES CHTY BCH ISAR NO CPUB OFF DAPC NO BCOT 0...
  15. 3cross

    Cisco DID PRI tandem through OPT 81 DID PRI

    It is receiving the 9 and the number from the Cisco and the trunks are at NCOS 3 here also which should alow the calls.
  16. 3cross

    Cisco DID PRI tandem through OPT 81 DID PRI

    It is a new setup. I will get some programming as soon as I can.
  17. 3cross

    Cisco DID PRI tandem through OPT 81 DID PRI

    Yes, it goes to the pilot dn of VM and the NCOS is set high enough.
  18. 3cross

    Cisco DID PRI tandem through OPT 81 DID PRI

    WE have a Cisco Call Manager sending calls (9xxxxxxx) to our Opt 81 rls 25.30 and want them to go out the local DID PRI. The calls hit the Opt 81 and go straight to VM. WE can see all the digits on the DCH coming from the Cisco. If you are on a trunk you can transfer a call out another trunk...
  19. 3cross

    Message waiting light across Tie line

    I hope someone can find the resolution. I have the same problem. Upgraded main site from 4.5 1000s to 5.5 1000E and message lites don't work anymore at the 4.5 1000s that uses SIP trunks for 4digit dialing and message lites. Everything works great but this. All patches are up to date on the far...

Part and Inventory Search

Back
Top