Search results for query: *

Hello I have 2 power plants that need to be connect it to each other by an async port; these systems are in different location, the Comunication is done at the moment using TDM multiplexors. We have now 2 2901 router with a WIC-2A/S card on each one to connect to the power system. I don’t know...

Thanks Telebub. Install new service update and setup wizard runs fine.

Hello. I’m installing a CallPilot 202i; Install the CallPilot Image on the server with no problems. Log in to the system and the system lunch the setup wizard, and part of the wizard do a platform Validity Check, I get a Server Bios Version Error and can’t continue with the wizard. I have...

Hello I need help to block the station name to go to the public network on SIP trunks. Telco Company is asking not to send the station name as part of the invite information when a station makes a call, because is causing problems on his call accounting system. There is a way to do this???? Here...

Hello, I’m setting up my first VPN L2L connection between ASA5510 and ASA5505. The tunnel comes up fine but can´t send traffic though the VPN, does anyone have an idea of what could be wrong ??? Here are the config. 5510 ASA Version 8.0(4) ! hostname MEXICALI ! interface Ethernet0/0 nameif...

Make a test calling the new Videoconference unit with a single channel. If the call is connect it rhe problem should be on the videoconfernce config.

those cards have factory problems, like 5 years ago Nortel change all the cards free.

If you didn't use a zone at first, will work but isn't good idea you will have problems latter. If you configure a zone now all IP configuration should have a zone configure, phones and trunks, so you have to one by one and configure a zone. Depending on your system it could be alot of work...

If you have a CPP core the pathc file unziped is more than 2 meg, but you can isntalled in a ZIP format, just takes longer but works fine

The clock is disable because you can’t have clock reference on PBX on T1 Cards and on E1 Cards it has to be one or the other. If your DCH is establish you should talk to the Telco and say that you can receive calls, I don’t know where you are installing the service, but some carriers need to do...

I'm not sure if will work but you can try it using a ACD instead of a phanton DN, create an ACD and in dcfw put the number you trying to reach and the pause.

Only Relese 3 will doit, but isn't free any more, you have to buy a licence to use it more than 30 days.

Thanks John. It was alwas the same TN I check it and it was a phantom. I will start to fix the problem

Hello, I have a CSE1000M PII system running SW 4.50W. The system is sending the next BUG and I don’t what is causing it. BUG304 TNTRANS found invalid ULPTR, TN A403, pointer 0xf240 15/04/2008 12:18:36 BUG0304 TNTRANS found invalid ULPTR, TN A403, pointer 0xf240 There I no service failing in...

My suggestion is to contact your vendor Engineer team, I’m sure they have documented all Nortel Benefits over Cisco.

QoS on the Network. Check That Firewall if exist have all ports use in call open

LD 17 Change in ATRN the promp CODE to 2 Change in PARM PCML to A LD 97 Change in XCTP DTMF to the tone value use were you are installing the system Change in SYSP INTL to yes. Also depend were you are installing you could need to add a new FTC table to be use in the customer an digital...

to now the TN you can use LD 32 comand CONV

This is how you can make the change from LD 11 REQ: chg TYPE: 3903 TN 4 1 9 5 ECHG yes ITEM key 16 mwk 8333 I think this is the VM service DN KEY press enter key until you receive REQ again Hope this can help you

Hello, I have been asked to interconnect a CSE1000S to a Alcatel Omnipcx Enterprise using H323 trunks. Does any body knows if is possible to do it ? I know using SIP trunks will be no problem but in this case the CSE1000S only have H323. Thanks for the help