Search results for query: *

All, I have trouble dialing a specific international number. I have been with AT&T troblshooting and they have escalated the trouble ticket till I got a very knowledgeable engineer. The trace shows that MY PRI that I am dialing out has a station ID showing a Unique International rather than a...

The below messages I am getting from the nortel side every time the an Avaya user tries to dial in I get the below. Any idea where sholud I be looking at on the Nortel Side if that apply. DCH 10 IMSG SETUP REF 00009CC5 CH 59 6 TOD 9:29:55 PROGRESS: ORIG ADDR IS NOT ISDN CALLING...

no digit conversion. both TGAR AND TARG =0. thanks

thanks for everybody's help. It turned out I had a bad port on the MSDL card. Now I can call to the avaya switch but the avaya cannot call my nortel extension,s. Is there a place that I have to change on the nortel side to allow the avaya to call my nortel extension's. thanks

...0 DES TRANS/OCEAN USR PRI DCHL 59 OTBF 32 PARM RS422 DTE DRAT 64KC CLOK EXT IFC ESS5 SIDE USR CNEG 1 RLS ID ** RCAP MBGA NO OVLR NO OVLS NO T200 3 T203 10 N200 3 N201 260 K 7 REQ **** OVL000 >ld 21 PT1000 REQ: prt TYPE: rdn...

I tried to use NI2 but I will not allow me to build the TIE Trunks. It gave me an error. the switch on the other sideis Avaya G 8 series!. any idea REQ NEW 23 TYPE TIE TN 59 1 DES TRANS/OCEAN PDCA 1 PCML MU CUST 0 NCOS 0 RTMB 26 1 SCH4792 RTMB

I had to go to ld 14 and out 23 channels than go to Ld 17 and out the D-channel. It stopped the errors scrolls. I noticed the PBX output the below. Any Idea? Thanks DCH:010 RECV FAIL (FDL NOT ALLOWED ) DCH:010 RECV FAIL (FDL NOT ALLOWED ) DCH:010 RECV FAIL (FDL NOT ALLOWED )

On this MSDL card I have few PRI so I canot disable it any suggestion? Thanks

I verified with the Avaya provider. they are the network and I am the user. Both sides are ESS5. for test I tried to change my side to NET but LD 17did not give me the option to change. I tried to enable the Loop and when I enabled it start scrolling with the avove errors. Any help please. Thanks

Yes it did. now I do we are trying to get the link up but it seems both D-channels are not communicating. Should I change my side to NET and test again. what do you think? Thanks

...ADAN DCH 10 CTYP MSDL GRP 1 DNUM 5 PORT 0 DES TRANS/OCEAN USR PRI DCHL 59 OTBF 32 PARM RS422 DTE DRAT 64KC CLOK EXT IFC ESS5 SIDE USR CNEG 1 RLS ID ** RCAP MBGA NO OVLR NO OVLS NO T200 3 T203 10 N200 3 N201 260 K 7...

...with the below. What am I doing wrong?. Is there a way to stop it from scrolling. Thanks DCH: 10 DISABLE INDICATION TIME: 13:38:09 REASON - **(00000086 ) DCH: 10 DISABLE INDICATION TIME: 13:38:09 REASON - **(00000086 ) DCH: 10 DISABLE INDICATION TIME: 13:38:09 REASON - **(00000086...

so the way it is programed with DID will not work and both sides has to be Tie trunks. The Nortel side is the Network and We have the D channel as NI2. Since it is not allowing us to do Tie changing the D-channel to other the NI-2 any suggestion?. Thanks

I have a question about the type of tunk type to connect Nortel to Avaya. a Point to point connection betwee the 2 PBX's . On the Nortel side my service provider programed the PRI with the DID trunks rather than TIE trunks. I was watching when he was doing the programing and for some reason...

Thanks for all your help. It did it by x01.

I am sorry I went and changed in LD 16 but when I went to Ld 21 to print the route again to check it is still TARG 01 and not 0. I dont know why it did not take the 0. Am I doing somthing wrong by not allowing me to change?. Any inputs will be greatly appreciated

Ihave changed the TARG in RDB to 0 and I tried to dial the trunk access code from a phone that is restricted and it still did not work. I have noticed the phone that I can have access to the trunk it has TGAR 0 and NCOS 4 The phone that I cannot dial from The TGAR is 1 and NCOS 4

I have the need to allow all users to dial access code to a Tie trunk between 2 PBX's. At this point some users can and some cannot. There is no way of changing all users phones the NCOS. Is there a way of doing it on the trunk?whwere can I go to program it?. Thanks in advance.

If I have to dial 4 digits access code and 4 digit extensions there is no point of going to all the trouble of joining the 2 pbx's and it will not be acceptd by the Management. Any suggestions please?. Thanks

How do I do that? Thanks