D-Channel continous error showing on terminal

[joeban]

Our service provider has programmed a tie link between an option 81C and an Avaya switch. When I tried to enable the PRI it started scrolling non stop with the below. What am I doing wrong?. Is there a way to stop it from scrolling.
Thanks

DCH: 10 DISABLE INDICATION TIME: 13:38:09
REASON - **(00000086 )

DCH: 10 DISABLE INDICATION TIME: 13:38:09
REASON - **(00000086 )

DCH: 10 DISABLE INDICATION TIME: 13:38:09
REASON - **(00000086 )

DCH: 10 DISABLE INDICATION TIME: 13:38:09
REASON - **(00000086 )

 

[bigindian65]

Post DCH config
make sure your IFC is ESS4 not dms or d250

Mato' Was'aka

 

[joeban]

It stopped scrolling but the below is the config for the D- Channel

REQ PRT
TYPE ADAN DCH 10

ADAN DCH 10
CTYP MSDL
GRP 1
DNUM 5
PORT 0
DES TRANS/OCEAN
USR PRI
DCHL 59
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC ESS5
SIDE USR
CNEG 1
RLS ID **
RCAP
MBGA NO
OVLR NO
OVLS NO
T200 3
T203 10
N200 3
N201 260
K 7

REQ

 

[bigindian65]

ESS5 is good to an Avaya. Has it stopped completly?

Mato' Was'aka

 

[joeban]

Yes it did. now I do we are trying to get the link up but it seems both D-channels are not communicating. Should I change my side to NET and test again. what do you think?
Thanks

 

[bigindian65]

Not much left, you verify the other end as ess5?

Mato' Was'aka

 

[joeban]

I verified with the Avaya provider. they are the network and I am the user. Both sides are ESS5. for test I tried to change my side to NET but LD 17did not give me the option to change. I tried to enable the Loop and when I enabled it start scrolling with the avove errors. Any help please.
Thanks

 

[bigindian65]

On an MSDL card? anything else on it, can you dis?
and enl msdl XX fdl? or enl dch 10 fdl?

Mato' Was'aka

 

[joeban]

On this MSDL card I have few PRI so I canot disable it any suggestion?
Thanks

 

[bigindian65]

TRy just the enl dch 10 fdl

Mato' Was'aka

 

[phonz1]

you can't change in LD17, would need to out and rebuild, but you both can't be NET anyways

 

[joeban]

I had to go to ld 14 and out 23 channels than go to Ld 17 and out the D-channel. It stopped the errors scrolls. I noticed the PBX output the below. Any Idea?
Thanks

DCH:010 RECV FAIL (FDL NOT ALLOWED )
DCH:010 RECV FAIL (FDL NOT ALLOWED )
DCH:010 RECV FAIL (FDL NOT ALLOWED )

 

[hawks]

Have you tried NI2? What type of switch is at the far end?

 

[joeban]

I tried to use NI2 but I will not allow me to build the TIE Trunks. It gave me an error. the switch on the other sideis Avaya G 8 series!. any idea

REQ NEW 23
TYPE TIE
TN 59 1
DES TRANS/OCEAN
PDCA 1
PCML MU
CUST 0
NCOS 0
RTMB 26 1

SCH4792
RTMB

 

[9201]

Post your RDB.

 

[joeban]

the below is the D-channel and the RDB. Thanks for your help.
REQ prt
TYPE adan dch 10

ADAN DCH 10
CTYP MSDL
GRP 1
DNUM 5
PORT 0
DES TRANS/OCEAN
USR PRI
DCHL 59
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC ESS5
SIDE USR
CNEG 1
RLS ID **
RCAP
MBGA NO
OVLR NO
OVLS NO
T200 3
T203 10
N200 3
N201 260
K 7

REQ ****
OVL000
>ld 21
PT1000

REQ: prt
TYPE: rdn
SCH0099 RDN?
TYPE: rdb
CUST 0
ROUT 26

TYPE RDB
CUST 00
ROUT 26
DES TRANS/OCEAN
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
IDEF NET
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC ESS5
SBN NO
PNI 00000
SRVC NNSF
NCNA YES
NCRD NO
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
CPUB OFF
DAPC NO
BCOT 0
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 426
TCPP NO
PII NO
TARG
CLEN 1
BILN NO
OABS
INST
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096

IENB 5


PAGE 002

TFD 0
VSS 0
VGD 6
DRNG NO
CDR NO
VRAT NO
MUS NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO

REQ:

 

[joeban]

thanks for everybody's help. It turned out I had a bad port on the MSDL card. Now I can call to the avaya switch but the avaya cannot call my nortel extension,s. Is there a place that I have to change on the nortel side to allow the avaya to call my nortel extension's.
thanks

 

[56BelAir]

No its automatic unless you are doing digit conversion, try turning on D-channel messaging in LD 96.
enl msgo 10
dis msgo 10
this will tel you if he is getting out to you. If no messeges across its on him.

 

[joeban]

no digit conversion. both TGAR AND TARG =0.
thanks

 

[joeban]

The below messages I am getting from the nortel side every time the an Avaya user tries to dial in I get the below. Any idea where sholud I be looking at on the Nortel Side if that apply.

DCH 10 IMSG SETUP REF 00009CC5 CH 59 6 TOD 9:29:55
PROGRESS: ORIG ADDR IS NOT ISDN
CALLING #:7132327989 NUM PLAN: NUM UNKNOWN/UNKNOWN (UNKNOWN)
CALLED #: NUM PLAN: NUM UNKNOWN/UNKNOWN (UNKNOWN)

DCH 10 OMSG REL COMP REF 00009CC5 CH 59 6 TOD 9:29:55
CAUSE :INCOMPLETE NUMBER

DCH 10 IMSG SETUP REF 00009FCE CH 59 7 TOD 9:30:03
PROGRESS: ORIG ADDR IS NOT ISDN
CALLING #:7132327989 NUM PLAN: NUM UNKNOWN/UNKNOWN (UNKNOWN)
CALLED #: NUM PLAN: NUM UNKNOWN/UNKNOWN (UNKNOWN)

DCH 10 OMSG REL COMP REF 00009FCE CH 59 7 TOD 9:30:03
CAUSE :INCOMPLETE NUMBER

DCH 10 IMSG SETUP REF 0000A335 CH 59 8 TOD 9:32:53
PROGRESS: ORIG ADDR IS NOT ISDN
CALLING #:7132327989 NUM PLAN: NUM UNKNOWN/UNKNOWN (UNKNOWN)
CALLED #: NUM PLAN: NUM UNKNOWN/UNKNOWN (UNKNOWN)

DCH 10 OMSG REL COMP REF 0000A335 CH 59 8 TOD 9:32:53
CAUSE :INCOMPLETE NUMBER