Search results for query: *

Has anyone ever had the ip address change after you powered it off and back on? Has anyone had the system say the 3 digits you enter are not valid but then when it ask you to reenter it takes them the 2nd time? I am going to call the place where I got the call pilot on monday because it was...

Hi I have a customer with an Avaya Partner I set up the hotline and put a single line wall phone there because it said it was okay and it works. Does anyone know if the alert station can be a single line phone also? Thanks

thank you all. Thanks for the information that the call pilot reboots when you unplug the line cord. I wired 2 jacks with 2 ext each and plugged them in and waited for the unit to reboot and it worked. thank you

it worked until i tried to have the 2 ext on one line cord going to the call pilot and then it quit until i put it back to 1 ext per port on the call pilot. however it took a few minutes after i put it back to 1 per line cord for it to start working. that is why i wanted to know if there is a...

i tried wiring up the jack with the 1st ext on the green/re and the 2nd on the black/yellow and it did not like it. when i checked the ports in the maintenance on the mics it said the ports were unavailable and i could not call the 2 exts. is there a special way to wire them?

the software version of the call pilot is Version 31.10.37.22 they have had a couple of times this month where someone calling in has just had ring no answer probably because both ext connected to the call pilot has been in use. it only has the 2 ports to connect to phone system. but in the...

Thank you I will try to check this out but I still have the problem of no one knows the higher level password. I only have the cust/ custpw1 and that does not let me put in some of the commands. Do you know of any back doors into programming? Thank you

It is the short one 2 shelves only.

I did a list config all and the processor was the only one that had 2 "u"'s the 765 had 01 02 03 04 that was why i was trying to find out what is programmed on it but can't get to certain commands. the only password I can get in on is cust / custpw1.

It has the following cards tn790 processor vintage 14 Q3.2.239.3 def R6 tn765 processor Intfc v22 tn777b network control v21 tn778 packet control v8 tn2182B tone clock v1 tn2464 DS1 Intfc however when I tried to use show could not get to that command. have checked with former vendor and they do...

I have a avaya Definity G3- version V6 and have verified that the ISDN-BRI Trunks is set for y and the ISDN-PRI is also y the only one that is no is ISDN-PRI over Pra con is n. They currently have a T-1 with a CSU on the back of the cabinet. Question? Would like to verify that this means it can...

Thank You again, I will try this as soon as I can get by there again.

I tried adding it but it said it was not a valid option. i used help command and went thru every button option but did not see anything it is an old system. Was hoping I was just missing something or that there is another area that I need to program to get the button to be available.

Thank You AvayaTier3, the Esc codes worked sometimes it took a few tries to get it to take but managed to get in change the time, verified the 911 calls are supposed to alert the console. new problem They do not have a console they are using 2 8434Dx phones as their front desk phones. I went...

Sorry just wanted to confirm what i had copied from ironhorse was what was needed to externally call forward a line. Wanted to verify that was how I needed to route it.

Thank You I will try this.

Hi, I am trying to find out what I am missing in my settings on my laptop. I am trying to connect to an old Avaya Definity that had an old link terminal the only other description was link Lucent no model number. If you turn it on it has garbage on screen and makes an obnoxiousness noise. I...

I need to change the time on a definity that I can not get into with my laptop and the terminal has died. can not find anything in my notes about changing time from the console. Any one know if it can be done? If it can how to change the time? thank you

thread799-1668222 Hi I have copied this from the above thread but since that was a uk system and mine is us wanted to make sure it will work. ironhorse17 (TechnicalUser) 1 Dec 11 12:03 Externally Call Forward a Phone: Note: You must have at least 4.1 software to execute this feature...

Hi Yes I made sure I am on direct connect and that the com port is the correct one and the baud rate. On hyper terminal I even tried the auto detect and it connects as vt100j @ 9600-8-n-1. it lets me log in but I can not get the function keys to work. I can type a command but it will not let me...