Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Avaya definity G3 - V6

Status
Not open for further replies.
ladytelcom

ladytelcom

Vendor
Joined
Nov 27, 2013
Messages
27
Location
US
I have a avaya Definity G3- version V6 and have verified that the ISDN-BRI Trunks is set for y and the ISDN-PRI is also y the only one that is no is ISDN-PRI over Pra con is n. They currently have a T-1 with a CSU on the back of the cabinet.
Question?
Would like to verify that this means it can have a PRI added? Also is there any thing else that needs to be checked the reason is that Cox is the current T-1 vendor and it is on their bill that it is a PRI but found out Cox could not get the PRI to work and that is why they have the T-1.
 
Sort by date Sort by votes
and what type of cabinet/processor?

Prologix/csi - you're good to go using a tn767 or tn464
G3R - you're good to go but must use a tn464
G3i/si - you'll need an available port on a packet interface board to assign each D Channel to. after that a tn767 or tn464 will support the B channels

-CL
 
Upvote 0 Downvote
correction on the last item... processor intf - not packet intf

-CL
 
Upvote 0 Downvote
It has the following cards
tn790 processor vintage 14 Q3.2.239.3 def R6
tn765 processor Intfc v22
tn777b network control v21
tn778 packet control v8
tn2182B tone clock v1
tn2464 DS1 Intfc
however when I tried to use show could not get to that command. have checked with former vendor and they do not have any other login or password than what I have.

Does anyone know a back door into the higher level for programming?
 
Upvote 0 Downvote
List config all" will show if you have an available port on the TN765 for the D Channel. If so, you have everything you need.


-CL
 
Upvote 0 Downvote
I did a list config all and the processor was the only one that had 2 "u"'s the 765 had 01 02 03 04 that was why i was trying to find out what is programmed on it but can't get to certain commands. the only password I can get in on is cust / custpw1.
 
Upvote 0 Downvote
try "list data-mod" for starters. See if any of the tn765 ports show up there. Is this a tall MCC cabinet or short SCC/XE type cabinet?

-CL
 
Upvote 0 Downvote
It is the short one 2 shelves only.
 
Upvote 0 Downvote
The short SCC/XE cabinets only had 1 Proc Intf slot. Each PI has 4 ports. Does this 3gsi already have 4 D channels assigned based on the "list data"? You can only have 4 D channels per PI board. 1 PI board per SCC/XE port network or 2 PI boards per MCC cabinet. Sounds like you might be maxed out if there are already 4 D channels assigned to this system.

-CL
 
Upvote 0 Downvote
Probably pre programmed the processor channels.
Below shows how to program when using tn765 processor interface instead of
ISDN-PRI over PACCON? y

changing to tn778 frees up isdn programmed to processor interface and you are
not limited to capacity of the tn765's that will work on your system.

You cannot mix ISDN-PRI? y with ISDN-PRI over PACCON? y
Must be one or the other. When changing from one to the other, all programming for
pri signaling groups and ds1 boards must be removed and readministered.

Code: 
display system-parameters customer-options                      Page   2 of   4
                                OPTIONAL FEATURES

                         ISDN-BRI Trunks? n  Restrict Call Forward Off Net? y
                                ISDN-PRI? y          Secondary Data Module? n
                    ISDN-PRI over PACCON? n          Station and Trunk MSP? y
-------------------------------------------------------------------------------
change communication-interface links                            Page   1 of   1

                                INTERFACE LINKS

                  Est    PI              Destination     DTE/
  Link   Enable   Conn   Ext    Prot   Digits     Brd    DCE   Identification
   1:      y       y    6999    BX25   eia               DTE   AUDIX
   2:      y       y    6992    ISDN              01A11        isdn1
   3:      y       y    6993    ISDN              01A12        isdn2
   4:      y       y    6994    ISDN              01A13        isdn3
--------------------------------------------------------------------------------
change communication-interface processor-channels               Page   1 of   4
                        PROCESSOR CHANNEL ASSIGNMENT
            Proc          Interface             Remote
            Chan  Appl.   Link  Chan  Priority  Proc Chan Machine-ID
              1:
              2:  isdn     2             h
              3:  isdn     3             h
              4:  isdn     4             h             
             59:  audix    1     1       h         1         1
--------------------------------------------------------------------------------
list configuration all                                                 Page   1

                              SYSTEM CONFIGURATION

Board                                                     Assigned Ports
Number   Board Type              Code     Vintage    u=unassigned t=tti p=psa
01A      PROCESSOR                TN790   000014
01A      PROCR INTERFACE 1        TN765   000016     01 u  u  u
01A      NETWORK CONTROL          TN777B  000023     01 02 03 04
01A      TONE/CLOCK               TN768   000007
02A      MAINTENANCE              TN775   000002
02A      TONE/CLOCK               TN768   000007
----------------------------------------------------------------------------------
change circuit-packs                                            Page   1 of   5
                              CIRCUIT PACKS

        Cabinet: 1                            Carrier: A
                                         Carrier Type: processor

 Slot Code  Sfx  Name                    Slot Code  Sfx  Name
                                          11: TN464  f   DS1 INTERFACE
  01: TN776      EXPANSION INTRFC         12: TN464  f   DS1 INTERFACE
  02: TN754      DIGITAL LINE             13: TN464  f   DS1 INTERFACE
--------------------------------------------------------------------------------
add ds1 1a11                                                    Page   1 of   2
                                DS1 CIRCUIT PACK

            Location: 01A11                           Name: isdn1
            Bit Rate: 1.544                    Line Coding: b8zs
   Line Compensation: 1                       Framing Mode: esf
      Signaling Mode: isdn-pri
             Connect: network
                                          Country Protocol: 1
                                          Protocol Version: b
Interface Companding: mulaw                            CRC? n
           Idle Code: 11111111
                              DCP/Analog Bearer Capability: 3.1kHz




      Slip Detection? n                 Near-end CSU Type: integrated
add ds1 1a12                                                    Page   1 of   2
                                DS1 CIRCUIT PACK

            Location: 01A12                           Name: isdn2
            Bit Rate: 1.544                    Line Coding: b8zs
   Line Compensation: 1                       Framing Mode: esf
      Signaling Mode: isdn-pri
             Connect: network
                                          Country Protocol: 1
                                          Protocol Version: b
Interface Companding: mulaw                            CRC? n
           Idle Code: 11111111
                              DCP/Analog Bearer Capability: 3.1kHz




      Slip Detection? n                 Near-end CSU Type: integrated
add ds1 1a13                                                    Page   1 of   2
                                DS1 CIRCUIT PACK

            Location: 01A13                           Name: isdn3
            Bit Rate: 1.544                    Line Coding: b8zs
   Line Compensation: 1                       Framing Mode: esf
      Signaling Mode: isdn-pri
             Connect: network
                                          Country Protocol: 1
                                          Protocol Version: b
Interface Companding: mulaw                            CRC? n
           Idle Code: 11111111
                              DCP/Analog Bearer Capability: 3.1kHz




      Slip Detection? n                 Near-end CSU Type: integrated
--------------------------------------------------------------------------------
list data-module                                                       Page   1

                               DATA MODULES

Ext.   Port     Type         Name                         COS  COR  TN  ISN

6992   01AXX02  procr-intf   idsn                         1    1    1
6993   01AXX03  procr-intf   isdn                         1    1    1
6994   01AXX04  procr-intf   isdn                         1    1    1
6995   01BXX02  procr-intf   idsn                         1    1    1
6996   01BXX03  procr-intf   isdn                         1    1    1
6997   01BXX04  procr-intf   isdn                         1    1    1
6998   01BXX01  procr-intf   AUDIX                        1    1    1
6999   01AXX01  procr-intf   AUDIX                        1    1    1
=================================================================================
add signaling-group 2                                           Page   1 of   5
                                SIGNALING GROUP

 Group Number: 2
                    Associated Signaling? y          Max number of NCA TSC: 0
                       Primary D-Channel: 1a1124      Max number of CA TSC: 0
                                                   Trunk Group for NCA TSC:
       Trunk Group for Channel Selection: 22
          Supplementary Service Protocol: a
add signaling-group 3                                           Page   1 of   5
                                SIGNALING GROUP

 Group Number: 3
                    Associated Signaling? y          Max number of NCA TSC: 0
                       Primary D-Channel: 1a1224      Max number of CA TSC: 0
                                                   Trunk Group for NCA TSC:
       Trunk Group for Channel Selection: 23
          Supplementary Service Protocol: a
add signaling-group 4                                           Page   1 of   5
                                SIGNALING GROUP

 Group Number: 4
                    Associated Signaling? y          Max number of NCA TSC: 0
                       Primary D-Channel: 1a1324      Max number of CA TSC: 0
                                                   Trunk Group for NCA TSC:
       Trunk Group for Channel Selection: 24
          Supplementary Service Protocol: a
--------------------------------------------------------------------------------

A great teacher, does not provide answers, but methods to teach others "How and where to find the answers"

bsh

40 years Bell, AT&T, Lucent, Avaya
Tier 3 for 30 years and counting
[URL unfurl="true"]http://bshtele.com[/url]
 
Upvote 0 Downvote
When all four data extensions are assigned for communication links:

Code: 
01A      PROCR INTERFACE 1        TN765   000016     01 02 03 04

A great teacher, does not provide answers, but methods to teach others "How and where to find the answers"

bsh

40 years Bell, AT&T, Lucent, Avaya
Tier 3 for 30 years and counting
[URL unfurl="true"]http://bshtele.com[/url]
 
Upvote 0 Downvote
Thank you I will try to check this out but I still have the problem of no one knows the higher level password. I only have the cust/ custpw1 and that does not let me put in some of the commands.
Do you know of any back doors into programming? Thank you
 
Upvote 0 Downvote
what commands are you not able to do? Click the link if you need help.

A great teacher, does not provide answers, but methods to teach others "How and where to find the answers"

bsh

40 years Bell, AT&T, Lucent, Avaya
Tier 3 for 30 years and counting
[URL unfurl="true"]http://bshtele.com[/url]
 
Upvote 0 Downvote
cust login should allow you to do all the commands shown in the examples
changing customer options would be what your login cannot do, if MSP are disabled as
shown on system-parameters customer-options, the login may not be able to do test or
busy / release commands.

A great teacher, does not provide answers, but methods to teach others "How and where to find the answers"

bsh

40 years Bell, AT&T, Lucent, Avaya
Tier 3 for 30 years and counting
[URL unfurl="true"]http://bshtele.com[/url]
 
Upvote 0 Downvote
Did you get this working?

A great teacher, does not provide answers, but methods to teach others "How and where to find the answers"

bsh

40 years Bell, AT&T, Lucent, Avaya
Tier 3 for 30 years and counting
[URL unfurl="true"]http://bshtele.com[/url]
 
Upvote 0 Downvote
Status
Not open for further replies.

Similar threads

A
  • Locked
  • Question Question
CMC Cabinet Connections for Definity G3
Replies
5
Views
605
dialtonebone
dialtonebone
A
  • Locked
Looking for Avaya DEFINITY G3csi R6 Tech / Media / Guidance
Replies
4
Views
656
AncientEnterprise
A
hunterrob
  • Locked
  • Question Question
Avaya EM200 removal
Replies
3
Views
462
dialtonebone
dialtonebone
BIS
  • Locked
  • Question Question
Avaya Infinity
Replies
1
Views
519
gnesvik
gnesvik
Saltylad
  • Locked
  • Question Question
Avaya Workplace
Replies
2
Views
532
SouthernKnight
SouthernKnight

Part and Inventory Search

Sponsor

Back
Top