Search results for query: *

not a pri just a t1 with dids coming over it, this phone is normally forward at night and during the weekend, just want to do the same thing, thought i could with an sdn

I have built a new app and sdn of 7200 and used ncfw of 7000 in load 23 when build 7200, i can dial the app and use it but when i try to forward my main set to it, which is a 3904, i get a busy signal, any ideas?

So I need to go into ld 23 and create a new acd dn with the same number i want to make my sdn? no cdn?

I have a 201i that is used for mailboxes only at the moment, I need to build an application for auto attendant ,we are going to forward the main phone to the sdn I build for this app. My question is do I need to build a new acq queue for this app or can I use the one that my mailboxes use?

I have a 600r 5.0, does anyone know the different anti-viruses i can install on this server.

I have had 2 callpilot 150s lose there memory. I reprogrammed one and it lasted about a year until this weekend when they took a sustained power outage, the other is just about 2 years old and never had any problems with until this long power outage, they are reprogramming fine, but will they...

you mean a number behind the key? it will not let me put a number in when i hit the call forward button

changed button and no change

same result on a different key. and yes i am dialing 9 and the number

yes i can dial fine. when the handset is on hook and i press the call forward key the display says release and try again, if the handset is off hook and i press the call forward key and put the number in it calls the number like normal without even noticeing that i pressed the call forward key.

i am needing to forward this extension at night to a answering service, i thought i had it, but i was wrong. when you press the call forward button it say release and try again. any suggestions? REQ: prt TYPE: 3902 TN 10 11 DATE PAGE DES DES 3 TN 010 0 00 11 TYPE 3902...

the short cable from the smart jack to the m1 cable is home made, and it is a tmdi, we own the circuit as well and the other day we ran to a loop 4 or 5 minutes, clean and when we turned it back to the 11 it started taking slips. my cc was red so i disabled and reenable it and the tmdi card it...

here is my ssck this is my on t1 the card goes straight into the smart jack. no adtran or anything. what is layer 1 .ssck 0 ENBL CLOCK ACTIVE CLOCK CONTROLLER - LOCKED TO SLOT 2 PREF - 2 SREF - FREE RUN AUTO SWREF CLK - ENBL NO ERROR IP DB PORT 1 DSBL IP DB PORT 2 DSBL IP...

...DTI TRK LOOP 2 TRSH CNT: BPV -010 SLIPD -000 SLIPR -000 LOSFA -002 OS_BPV -000 OS_LOSFA-001 OS_YEL -000 .prt DTI002 .**** OVL000 >ld 117 OAM000 MEM AVAIL: (U/P): 2668137 USED U P: 317654 61632 TOT: 3047423 DISK RECS AVAIL: 256 SURVIVABILITY AVAIL...

Has anyone ever had there M1 disable ports for no reason. my customer started calling me during the day yesterday with different exts. out i checked them and they were disabled, sometimes all the ports on the card would be disabled, weird. it happened to both digital and analog exts. Help

i have a callpilot 150 with 8 voice channels, i have 5 lines in a hunt group the voice mail is set to answer using ringing service and a services button so they can turn it on and off. the customer says that sometimes a line rings all the phones when services are on. is there any way for me to...

i have got my cdr streaming, but i dont see any in coming calls only out going and i have a test phone set up with cls icda and that works fine, but what should i see when an incoming call comes in? here is some cdr: & 0000 0000 S 014 00 2130...

i have a call accounting software for my customer i have set up a sdi port as cty and set cdr on my routes to yes, im not getting any streaming data when i connect to that port with my pc and terminal session, any ideas?

ok route 2 (20 channels) is targ 1 the sets that will use this route have a tgar of 0 route 6 has a targ of 0 and the sets that use that route have a tgar of 1 so i have to change route 2s sets because they can use both routes?

thanks guys the entry 1 in the existing rli worked like a charm