Search results for query: *

I'm looking for a way to use DISM to create a backup of the User folder and be able to reapply that image back to the drive when needed. I have an image created but I can't get it to apply. I've used the instructions to move the User folders to a non-SSD drive and would like to keep a separate...

Just an update to close this thread. I couldn't figure out what was causing it to fail during the last step of the upgrade. I've tested attaching a second drive from a test 2003 R2 x64 VM to a fresh 2012 VM and it looks like all the NTFS right transfer (of course with the exception of the local...

I'm getting ready to take this copy change the name and IP setup a new file share and make it reflect the current share (smaller scale though). Then I'm going to disconnect that drive then slide it to a new 2012 VM and see if the NTFS rights carry over. If that works then I'm good, if not then...

It's only a file server, no other roles. At one point I did have VBox installed and Commvault backup but I've removed all that software.

I'm almost at the point of a fresh install but I need to make sure that the data drive will hold on to all the permissions for the shares if I attach it to a new install. I have about 1.5TB of users files and a share tree that's very large. All folders are set with NTFS perms so I think they...

Both are standard not enterprise, the VM host is vCenter 6.0.0 build 5318203. Just tried again with different ISO and it still fails at the same spot. The only errors I can plainly see are about the media player dll but I doubt that should cause it to fail. I'm going to wipe the logs and keep...

Has anyone gotten this to complete all the way? I get to the last step and at 62% of transferring settings and programs it craps out. This is a VM and I've tried with the vmtools and without. The only constant so far it that it complains about the VMCI might not work after upgrade. I've tried...

Looks like I found the problem, the COR was set to only allow internal ext (since we have never had to do this before. Changed it to a COR that can call 800 numbers and it looks like it's working now

Hi all, we are getting ready to setup a new call center in a remote location that is NOT connected to us. I'm looking for a way to transfer calls while still in the main number vector (auto attendant vector). I have setup an extension for transfers and that works from any ext that has answered a...

I didn't think of that, as long as they don't collide with my local exchanges. I'll update this once I have some more info. Thanks joe2938

Hmmmm, I'm not sure what they use. I have a 4 digit 7xxx range and some leftover outside that range for our last DP change (10 years ago). I think I would prefer a TAC then dial since there are more than 10 possible properties.

I think they'll want it close to the way the other properties are setup. Pick up phone, dial a TAC and then ext and it will ring at a desk far,far away. I just have no clue how those link are configured and I'm trying to get info from them. So if a can setup a IP trunk link to their system...

I've been asked to figure out how to go about connecting our current PBX (G3siV12 Software Version: R012i.01.1.414.1) to our HQ in a different state over our WAN link. Does anybody have a good place to start? - lol Remote system is a Cisco VoIP system (don't have any more detail yet). Since...

Well they finally fixed it, calling tech said the circuit was set for dialtone and not wink-start. Don't know how they let that happen and why it took almost a week for them to compare it to my other circuit to check the config when I told them that first. Hopefully nobody else runs in to this...

The card I swapped? yeah it was tested good when my service company sent the big box of cards to me. I'm also getting the same results as with the card I pulled. I thinks it's highly unlikely that both cards would fail in the same way. The original card was a vintage 8 and the current is vintage...

display trunk-group 14 Page 1 of 11 TRUNK GROUP Group Number: 14 Group Type: tie CDR Reports: y Group Name: Incoming T1 COR: 1 TN: 1 TAC: 279 Direction...

They did that yesterday, guy hooked up the line and said he was able to seize the trunk and make a call. Settings on his tester matched what I had printed out from my system. I did get a call and email that they made a change and to retest but I'm still getting the same issue. There's gotta be...

Did that, so far they can't find it and wouldn't even admit to possible changes, because this issue started at 1pm in the afternoon on a Thursday (and they don't do maintenance during the week - yeah right). So far each tech I talked with said the circuit was matching the settings I have in my...

I know right, no sense at all. here's the board test test board a16 Page 1 TEST RESULTS Port Maintenance Name Alt. Name Test No. Result Error Code 01A16 DS1-BD...

With my G3 I use an FTP client to backup all my announcement from my VAL board.