Search results for query: *

It's about 5 years. We had it with all default features. Is there any dianostic tools for it?

It is more internal. Besides, we are far from the limit; only 60 phones.

Does anybody experience this situation? We have the system several year and recently encounter this. It happens to both digital and VoIP phones, but randomly and cannot be reproduced. In short, when it happend people hangs up and makes call again, and it's fine. I cannot figure out what...

We have IPO 406 V2, 30 x 5610 VoIP phoes, 10 x 5410 digital phones. The system is running fine for about 4 year. Recently, only the big boss complain that on his phone, everybody can hear him but he cannot hear from the others. Besides, when the others hang up, his call session never release...

Does anybody know the reason why the IP Phone 1608 cannot establish connection with the IPO 406 Version 2 over a distance. The situation and set-up we have are the following: - 2 POE switches between 2 buildings connected via a 1800 ft single-mode fiber trunk. - The main building switch has...

I am new to MS Access, and try to learn and use 2007 version. So far I can do basic things but running into one difficulty that I don't have any clues to find solution. Any hints, and examples will be very much appreciated. I have the following tables: System table with 4 entries...

Because we only need two or 3 more conference phones besides of the two already used. 8-port analog module is the lowest option and it also costly; Besides, using more analog lines will reduce the available channel for the VCM, right? If ATA can be used, it probably cheaper; hat why i ask.

I am sorry guys. I am looking for VoIP ATA for the analog phones since we only have two analog ports, but adding another 8-ports analog to a VoIP capable PBX is not a good choice and also we try to use VoIP as much as possible. Thanks

Does anybody know a reasonable cost ATA device that works with both Polycom Sounstation2 and IPO 406 Version 2?

Thanks to you guys. I made the Flash Time on the SoundStaion2 to 600ms and it work.

Yes I did. Then it show "FLASH" on screen. Could somebody tell me after hitting "Conference" or "Flash", what should be expected beside the word flash, such as dial tone, etc.?

It is case 2. I did check on the Call Manager, and there is no conflict, it is Conderence Add. Can you give a little guide how to use the SSA feature? Thanks

Hello guys, I searched and found several hits about this. However, when I tried, none of them work. That's why I have to open a new one. My question is that if IPO 4.2.11 still support this? Next, what type of indication the IPO supposes to tell instead of Analogue Extension Phone? Here is...

I got it working. By the way, the icmp rules there are for testing purpose.

TomMills, You probably think that there is an IP conflict or whatever, but notice that all other 40 5610SW phones are working fine. But for your answer, IPO a.b.c.1 and pc running manager a.c.b.3, mask is 255.255.255.0.

I am using the IP Office, not http server, and I did followed the document. I made all 5610SW phone successfully, but not the 1603 and 1608.

Yes, tlpeter. We tried to hook them up, but no success. Is there any tricks to set them up?

No, sir. I have not successed with vpn1 yet; once i am done with the first one, I will try with the second. The second one attributes will have all separate nat, acls. Specifically, the user got through the challenge, but cannot access the webmail. Using wireshark on the webmail, I can see the...

I have been trying to config a PIX 515E, version 8.0(4), with remote access vpn groups that has limitted access to the mailserver through http (webmail). I got the first vpn-user group throught the tunnel, but cannot get anything else. Can somebody look at the config below and give some helps...

I inherited 2 phone 1603 and 1608 but cannot make it work with my IP office 406 v2. Can somebody tell me how and if necessary point me or past me the text file or bin fole for them please. Thanks