Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. getsomesun1

    UCx SIP trunk to Avaya Session Manager

    I know nothing about Aura but have connected SIP Trunks to Avaya Call Manager. Since they are both Avaya maybe they will be similar. The Avaya CM prefers signaling over TCP not UDP. In the UCx under SIP Settings / Advanced SIP settings enter tcpenable = yes in Other SIP settings. See if this...
  2. getsomesun1

    InfinityOne Mobile App for Android

    Although the app is available in the Play Store it will only work on the InfinityOne Beta software on the UCx itself. My understanding is that it is close to GA but not quite there yet. Once the GA is released it will work just fine. www.ucxdirect.com
  3. getsomesun1

    IVR - Send callers to extension on a different UCx

    I didn't have notify on for this thread. I do now. If you have issue post it and I will try to get back to you quickly. It will work. ;o) www.ucxdirect.com
  4. getsomesun1

    IVR - Send callers to extension on a different UCx

    You will accomplish this through Directories. Assuming you are using Extension Directory as your Direct Dial choice in the IVR you will add the Ext's from the other UCx to the Directory of the UCx that is answering the calls. This also assumes that you have a coordinated Dialing plan between...
  5. getsomesun1

    UCX 50 - Static on inbound calls.

    I agree with ucxguy. Follow these instructions for ec_tune to optimize your analog trunks. https://www.emetrotel.com/tsd/content/optimizing-trunk-settings www.ucxdirect.com
  6. getsomesun1

    Nortel - Issue Calling certain phone numbers

    Based on this sentence - When calling any of these phone numbers which have problems, it seems to just not ring and immediately ends the call it is possible there is something off in your Route? Have you made calls while watching BCM Monitor to see if the call is even getting out to the PSTN...
  7. getsomesun1

    BCM 50 rings half ring

    If the Line is assigned to the Table that the CCR tree is assigned to and it is set to 0 rings then the AA should answer on the first ring especially if you have PRI. If you are getting a Chirp on some phones then I would think you have that line assigned to the phones. If the AA is not...
  8. getsomesun1

    Best way to connect old norstar 8x24 and UCx server

    I agree with telcodog. A digital gateway that is connected to the UCx over the WAN/LAN to replace the Norstar. Then you have one system that handles all phones. www.ucxdirect.com
  9. getsomesun1

    Bcm450 R6 with CEC card, maximum number of Digital sets

    I think the problem is in your telephony resources. The system comes default with a mix of IP and Digital. It's been quite a few years since I have worked on BCM but I think your problem lays there. www.ucxdirect.com
  10. getsomesun1

    Planning for Hybrid UCx/61c

    TN's are defined pretty much the same LSCU. Commands will be pretty much the same as well such as the following. disc loop, shelf, card disable card disu loop, shelf, card, unit disable unit dsp_active cabinet Dsps available for cabinet? dsp_conn cabinet returns the dsp connection server...
  11. getsomesun1

    Yealink Cordless

    Register the Base as a SIP Extension and then register the Handset to the base. Everything you need to know is located here. http://support.yealink.com/documentFront/forwardToDocumentDetailPage?documentId=110 www.ucxdirect.com
  12. getsomesun1

    SIP doorphone keeps going offline ...

    UCxguy brings up a good point. You can also have another device connecting to the network that may have the same address statically assigned. to confirm this, get IP address of the doorphone, make sure it is pingable. then disconnect it from the network and try to ping again. If you get a...
  13. getsomesun1

    SIP doorphone keeps going offline ...

    Have a few questions. Is the other doorphone also connected to the UCx? If so, I am sure you compared the ext programming? When you say you pull the cable from the switch and power cycle, do you mean it is connected to a POE switch and when disconnected and reconnected it power cycles the...
  14. getsomesun1

    Temp Closing

    You can Also Use Misc. Destinations PBX Tab Misc. Destination Description = Temp Close Dial = *280 (Assuming the Call Flow Control you built above is your first one) Then in you IVR add a Option that is not in your IVR recording like 9*0 or anything that is not common. In your IVR add the...
  15. getsomesun1

    Voice mail volume ...

    You can download the Greetings to your PC and load them into a Audio program to raise or lower the volume level. Then re-upload them back into the UCx. It works, we have done it. www.ucxdirect.com
  16. getsomesun1

    UCX50 default voicemail message

    Go to Voicemail Settings / Dialplan behavior and put a check in the Box next to Disable Standard Prompt. This is VoiceMail wide. www.ucxdirect.com
  17. getsomesun1

    UCx50 PRI

    You must use the EmetroTel SSD. It supplies the software needed to convert to a Digital Gateway. www.ucxdirect.com
  18. getsomesun1

    ChannelSpy

    Good fix. Did anyone look at using Custom Context to do the same thing. I did not test in Lab system but I have used Custom Contexts in the past to disallow features on Extensions. Just a thought. It may be a little easier than writing code. www.ucxdirect.com EmetroTel Stocking Distributer
  19. getsomesun1

    Rolling pin for conference room?

    I don't believe you can have the system auto-magically change the PIN but what you might consider is to create a separate group and user account for moderators, the moderator group should only have access to this page and not the other system admin pages. After each Conference call you can have...
  20. getsomesun1

    Dual PRI Trunks

    Without a lot of information I will give this a shot. You have PRI's at each location. I would assume that you have a outbound route built at each location. Something like 9_North_American where you have your dial patterns identified. I am also going to assume you have a SIP trunk Built between...

Part and Inventory Search

Back
Top