Search results for query: *

I found a company on on-line last week doing free on-line Cisco courses. I cannot remember their name. Can anyone help

Yes, that's how it ought to work, each SSID is mapped to an individual Vlan

Are the P.C's on vlan 10 using the vlan 10 interface address as thier default gateway? Nice

What other switch are you connecting the 5406 to. In any event it is fine, just remember to use 802.1Q trunking on the Cisco, make sure they are both trunking the same vlans and the same management vlan. Otherwise it's all good

Hello. If you are running MSTP on the Procurves then you should be able to work with Cisco PVST, I have had this working not problems. As with IST and CIST and CST think of 3 circles inside each other, IST is the inner circle it controls the local spanning instance of say MSTP, CIST controls...

If you want to stack them in the 3com XRN or Cisco Stackwise sense were you have dual redundant paths then the answer is no. You can fix it up to make it look like the switches are stacked by using MSTP (Multiple Spanning Tree) so you have two (or one) root, the top switches switch traffic out...

Hello You need to go to the interface command prompt of the interface you want to monitor an type in "monitor" The go to the global configuration context and type in "mirrorport [port number]" I think that's the right way around

Cheer lads I have sorted mine out, I place both of the Softconsole machines into the voice vlan and hey presto, it all works, all of the P.C still work, i.e outlook, etc,etc It is strange that the BLF's sometimes worked since a broadcast should not be forwarded across a Vlan interface. Nice

Hello, I have the same issue with Softconsole not worlking on 3.1(65). This company has three sites, all linked via LES circuits, the links are rounted so each office has IPPhones in thier own subnets. They have two consoles, which are on different subnets to the IPO and the BLF do work...

IPStanding, I have also seen this, but on a 412, every 30mins we lost connectivity to the IPO, only a reboot cured the problem. we ran a protocol sniffer on the IPO port but did not see anything unusual. We suspected an IDS on the network or a LaBrea Tarpit. The customer was looking for a...

From your config it does not look like you are putting the P.C's into the back of the phones. Are you using one port per device?

What are you using the network for, voice and data or just data?

Add the correct VLAN's to 'trk1' conf)#VLAN 1 trk1 untagged conf)#VLAN 2 trk1 tagged conf)#VLAN 3 trk1 tagged do this on both sides

The command is: (conf)#trunk A1,A2 trk1 The trunk configuration must be performed on both sides of the trunk before the redundant links are connected. Port trunking has implications for VLAN configuration. Because aggregated ports cannot be configured individually for VLAN membership, the...

The IEEE standard 802.3ad, also known as LACP, is based on Cisco’s Port Aggregation Protocol (PAgP). LACP was standardized to allow a switch to automatically recognize coterminous, full duplex, same-speed links between itself and another LACP-compliant switch. Although LACP can automatically...

Trunked links (HP Term for what cisco calls fastether channel) will operate from the perspective of RSTP as a single link. Trunk the links, then add Vlan to the links.

That's all you need to do. What do you mean timing problems, if you are referring to the Blocking, Listening, Learning, Forwarding timers, I would suggest that you leave them as they are, any alteration of these timers can cause the network to become unstable. Nice

RSTP By default all of the ports are treated as edge ports, cisco's implementation of port-fast was taken on in the RSTP protocol. When an RSTP port sees BPDU arriving it understands that it is not an edge port and must take part in RSTP. Redundant links are automatically configured due to...

You must turn on: 1. IP routing on the switch (conf)# ip routing <cr> 2. In the DHCP server use options in the data scope to tell the IP Phone to boot into the Voice VLAN. Option 176 46xx Options TFTPSRVR=X.X.X.X, L2Q=1. L2QVLAN=(VLAN OF THE VOICE) 3. Use IP Helper addresses on the voice...

If the frames sent to the non-vlan aware switch are untagged the non-vlan aware switch will treat them as normal and forward the frames based on source/destination mac addresses Nice