Search results for query: *

Good morning My name is Paolo and I write from Italy I'm sorry for my bad english I have encountered a frequent problem on cisco 3905 phones: The POE port fails and the phone no longer works if you connect an external power supply to the phone the phone works. The phone no longer receives energy...

Good Morning I would like some information on the OPI 3213 in MD110 BC13 MX-ONE TSW, Can You see the caller's number before to answer? Thank You

I know the method (;) but the sistem does not respond because the channel 1-0-60-0 is not free, I solved with the RFBOI: bipos = 1-0-60 (niu) and another login. thank You, Paolo

what is the correct procedure to make the change of the disk with bc13tsw? I have this sequence: bleqi:equ=1-0-60-0; fimoe:subfs=syssubfs21; iosie:node=sysn,iodev=sysdisk2; change HDU iosii:node=sysn,iodev=sysdisk2,btype=ata,subfs=syssubfs21; fimoi:subfs=syssubfs21; bleqe:equ=1-0-60-0,allfm=yes...

I have try with numtyp= 0,1,3,4,5 but follow me do not work is there anoter command for to set the rx call? Thank You Paolo

If I change NUMTYP=0 in NUTRI the call in input direct to extension do not work, today if is possible I try another value of numtyp Thank You for help

Sorry nutrp is not easy to read in the first message, <NUTRP:ENTRY=54988; NUMBER CONVERSION DATA ENTRY=54988, CNVTYP=0, NUMTYP=2, TRC=5, CONT=0 END in the printout any parameter are empty The souce command extrat in the pcregen is: NUTRI:ENTRY=54988,CNVTYP=0,TRC=5,CONT=0,NUMTYP=2; Paolo

This is the configuration: The rou of input call is ROU1 <ROCAP:ROU=1; ROUTE CATEGORY DATA ROU SEL TRM SERV 1 5110000010000010 5 2101000001 ------------------------------------------ NODG DIST DISL TRAF SIG BCAP 0 30 128 00151514...

Thank You for attention yes follow me in another phone or the cell work, I know another office with MD110 bc12 release and follow me work, omly follow me direct to MD110 with MX-ONE do not work in the (same or itself) MD110 before the upgrade MX-ONE follow me work good the procedure of...

Is difficult for my because I do not know well englis: The telephone of my residence is not un extension of MD110. Mi residence is connect to the telephone net of the city,(telecom italia) . In my office there is the md110 with TLU76 trunk isdn connect to the city, (telecom italia). if I know...

Sorry in the first time I do not have write a good question: Mi problem is not to make diversion with MD110, mi problen is to receive the pubblic diversion with MD110 If I dial *21*(number of office where is MD110)# in the telepone of my home, the call directly at my home when there is BC12 go...

Sorry I do not have write a good question: Mi problem is not to make diversion with MD110, mi problen is to receive the pubblic diversion with MD110 If I make *21*(number of office where is MD110)# in the telepone of my home, the call directly at my home when there is BC12 go to telepone of...

Hi I am sorry for my bed englis but I write from Italy I work in a system of MD110, the system is increase in release mx-one past release is bc12. in past release (bc12) is possible to make diversion of une pubblic esternal number to one number of the md110, with the new release (MX-ONE)...

HI bpczi I have a problem with drg22 I have write a question in anoter pare of this forum, now I repeat for show you: I have configure 1 phone DBC4222-voip, with the same parameter(GESPI GEDII IPEXI) of the DRG22, the digital phone work ok, if I call when is busy there is the busy tone, the...

Today I do not work, Tomorrow I go to check the SERV of the route, but I have not problem for to make calls with analogue phone, my problem is to receive: if I receiwe 2 calls, the first call is ok, but the second call do not give the busy tone, and the analogue phone receive a BEEP for...

I have configure 1 phone DBC422-voip, with the same parameter of the DRG22, the digital phone work ok, if I call when is busy there is the busy tone, the analogue phone connect to DRG22 do not work ok, if I call when busy there are the free tone, and the analogue phone connect to DRG22 have a...

dig 2 e 3 of the serv are = 0, maibe is there anoter problem thanks for the help best regard paolo

I am italian and I am sorry for my englis not good I have instal the drg 22, analogic telephone work ok. I have a problem with the second call to the analogic extension: when the extension analogic is busy, if I make a new call there are not the busy tone, ahd the analogic estension have a...

Guarda questi appunti e vedi se riesci a programmarlo, poi fammi sapere come va. Io ho messo in funzione i telefoni, ma ho problemi con le chiamate entranti. Il secondo chiamante non riceve l'occupato. se sai dove si deve intervenire fammi sapere. Paolo. Il DRG22 come impostazioni di fabbrica...

Ciao Alex scusa se entro qui raramente. scrivimi via mail paolo@omniway.sm a presto Paolo