Search results for query: *

Yea... its Com 1

Ok so tried... 513 and 4410 and 4425 baud: 9600 Data bits: 8 Parity: None stop bits: 1 Flow Control: tried "Hardware", "None", and "Xon / Xoff" Manual login: Yes When Hardware flow control is on it freezes/crashes DSA and ASA When Hardware flow control = None or Xon / Xoff = blinking curser...

Huh... I dont see about 1/2 those options under edit> properties of voice system I have DSA R1.5.06 and ASA 3.0.8

Hi guys, Here is what i'm trying to do, PC serial port connecting through 9 pin to 25 pin and simple 355A adapter to the Active Terminal port on the back of SPE-A in my Definity G3 What should the Port setting / Delay settings on DSA or ASA selected direct connect. Tried emulation 513 and...

Ok well got the Maintenance book for Definity Enterprise comunication server And Instialization and recovery is just no help Can't get shadowing to work Can't get it to refresh Handshaking is Fine which PDF seems to focus on for some reason. All bootup tests pass, have a freshly made back up...

Ok Guys I've replaced the MSS board and Disk drive... and All tests are passing now!!!! So I think I'm ready to boot this SPE-B back up Could someone help me with steps on that? sitting at <SPE-B-LOCKED> on the terminal screen commands are r - reboot from primary s - rebbot from secondary...

Ok figured out the stupid test timeout error... Guess My Carrier doesn't want to go through the test all circuit packs (default), as it times out half way through the testing everytime... All Memory boards Pass all their Tests Now The Errors come at, MSS Passed Disk Harddrive...

Had a week off, So about to order a (32Mb) TN1650B V4 from ebay and install it... Would this be a fare assumption since I got the test time exceeded error on this memory board? Thanks for everything so far!

Port Maintenance On Alt Alarm Svc Ack? Date Date Name Brd? Name Type State 1 2 Alarmed Resolved DLY-MTCE n MAJOR 01/02/01:33 00/00/00:00 01B DUP-CHL n MAJOR...

TGIF Guys! I physically locked both SPE-a and SPE-b over to the A side which then lit an LED and actually change status to locked SPE-A in <status SPE> I found out I needed to put terminal in the standby port in back of cabnet to see what SPE-B was up to. After removing disk drive and swapping...

Sorry That link PBXTech posted just pulls up a blank page... I'd love to have the maintenance Doc for this switch If you guys have a working link...

Hey PBXTech and AvayaTier3, In regards to the Power down of SPE-B Do you mean just Busyout SPE-B? Or actually pull the power plugs for the whole 01B Carrier with SPE-B in it? Or just pull out the Card in slot Dupn Interface?

Ok tried ejecting the MO disk from the troubled 01B Carrier with the standby SPE-B... Pushed it back in and got a green flicker nothing major. ran the Command list config software long and got error: Standby SPE has inadequate health to proceed, for information use 'status spe' Status SPE...

Inbound all depends on the Asterisk server and the SIP Telecom ISP your number is ported to... not alot to troubleshoot on the Avaya PBX

Hi PBXTech, Can I follow your walkthrough without effecting users on the system?

Searching this great site I found some commands to run... Definity Flavor is System: G3rV11 Software Version: R011r.03.2.536.1 Status Spe PROCESSOR COMPLEX Duplicated? yes SPE Selected: spe a locked active Standby Busied...

Sorry I inherited this Definity setup, could an external Tape backup server be handling the save translations? and I would simply never use this command?

Total Noob with Definity. Should have asked what commands should I use to start troubleshooting... What TN Card is the Flash card in? What is the SPE? maybe a quick overview on the Definity duplication process might help me. What I'm looking at is a Definity 10 Cabnet monster...

System: G3 Version: V11 Tring to save translations Error: Cannot access the standby SPE at this time ??