I set up the paging at the facility that has the ZPM 9 connected to the Call manager, FXS port, and it works. I did read the information you provided in the link, and it states that a station port requires the use of a TAM B in addition to the ZPM 3.
Thank you for your help. You were...
At one of the two sites using the POTS FXS-POTS line, we are connecting directly to a Bogen ZPM9. that tells me that we can connect to something other than a TAM-B.
G.W.North
We have a facility tied into our Cisco VoIP network. Recently, they were switched from Centrex Lines to a PRI line, which gives them lower operational cost per month, and greater bandwidth. The problem is that they are a service oriented agency, and routinely call their customers. When they...
Is there something special I need to know about the F9600 US model PBX? I'm trying to install a PRI card in the machine, and create a Trunk Group for it. I used exactly the same command, and filled the appropriate fields with the same values that I used with our MS PBX. I can successfully...
Did you assign the ACD user phones as part of an ACD group, and as ADC agents? When you make a station and ACD agent, you then have to use the "cha acdcd" command to set up the COS, RSM, and FRL of the station.
GWNorth
Perform a "dis pkgs" command on each of your sl and dl line cards. This will show you which equipment numbers are in a LLO condition. Then, it's a simple matter of following the cross-connect path to the appropriate wiring closet, and then to the jack. This won't tell you what room the jack...
Seadoo2000, thank you for taking interest in this thread. We were able to resolve the issue witin of few days of the original post. We had to shut down and reboot the voicemail system. The Innovation engineers looked at the programming and were able to tweek the settings. Our voicemail...
We have replaced the Fujitsu R9600US model PBX at one of our sites with VoIP. We would like to use the PBX as a single cabinet rather than the two cabinet PBX that was originally set up. Our manuals cover the XL, M, MS, ES, and VS model units. I don't have a manual for the US. I need to know...
Can I make an F9600 Platform work with Loop Start Trunks for Voice-mail? Altura Techs told me that I can't. Our network has Fujitsu F9600 platforms as far as 200 miles distant. The CO where the PBX is located is changing their facilities to all loop start trunks.
G.W.North
You can't restrict individual numbers from being blocked. But you can restrict individual extensions from accessing outgoing trunks through RSM/FRL/COS assignments. If you really know your stuff, you can also go into the ARSC and ARSR tables to enable/disable dialing to particualr area/office...
telm59 is correct. I administrate an F9600 network and had been working with Fujitsu for years. When Fujitsu got out of the PBX industry, they sold their remaining hardware and support service to Altura Communications. I currently work with the branch out of Southfield Michigan and they are...
If your local CO sends your DID's to you through your DNIS trunk, then as stated above, simply use the command - DIS DNIS - and the incoming digits, and where they are pointed to (the final extension) will be listed. If using Windowss-based EMML, make sure to click on the "output" pulldown menu...
ISO informaition for installing and configuring a stand-alone Music-on-Hold unit with messaging capability, on a Cisco IP Phone facility. The VoIP system at the site is part of a large network, but requires messaging tailored to the specific facility.
Thanks.
This is a fairly complex procedure requiring knowledge of routing commands. If you are not familiar with these, it's best to contact Altura for assistance. If you are, then use the "ass arsr" command to create route tables for long distance, local area code calls, and local calls. Then use...
No I haven't. I'm new to this forum. We still have an F9600 networket up as we slowly migrate to VoIP. We actually have both Cisco VoiP and Fujitsu F9600 working togehter on the same network. Our voicemial server works with both products as well. So, I'm in research mode. Though I am F9600...
Does anybody have information about connecting two Fujitsu F9600 PBX units together via FIPN in a lab setting (not using a CO provided T1 connection). We have two PBX's and would like to set up one as a backup for one of our sites. To do so requires that we load a backup from that site into...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.