Search results for query: *

Thanks for the reply. I need to clarify some things. The phone is a 2004. There is a VPN established through two Sonicawalls between the home office in question and corporate. Both LAN interfaces on the BCM have IPs. One is a 10.x.x.x behind the firewall, the other is a public IP with no...

I have a BCM 400 with several sites connected that work fine over the Public Interface. I am looking at setting up some home users through VPN (Sonicwall), however when the phones connect there is one way audio. I make make a call and my voice is heard, but I cannot hear the other party. Im...

That works thanks. But with the new format it is still reading the date format of mm/dd/yyyy which causes the sort to not work. Did I miss a step about changing the cell type from date to textbox?

Hi I have a spreadsheet with two date colums. Column H is formated in MM/DD/YYYY. Column B Is formated the same. This data is exported from a DB in this format. I need Column B to be in YYYYMM Format, it shows us year and period. I need a formula that will take this info from column H and...

Pretty sure you dont need it, but yes I've tried it with the 9 which is the destination code. I'm thinking the flash is too old. I have a NAM that I'm going to try instead. These systems have worked together for years when we had analog lines. Recently disconnected all the analogs leaving only...

Same problem when choosing Pool 2. No notification unless a line is picked and then it works for a couple days and then quits

Yes 9 or no 9 does not work with pool specified. If line is specified it will work with no 9.

I have a MICS 4.1 with PRI attached to Startalk Flash VM. If I specify Pool 1 as the outdial for message notification it will not outdial. If I specify a line it will outdial for about a week then quit until a different line number is specified. There are no analog lines attached to the system...

IS THERE A WAY TO UPGRADE THE 4.0 NAM TO 4.1 WITHOUT LOSING MAILBOXES AND PROGRAMMING? WE HAVE APPROX. 80 USERS AND PROGRAMMING WOULD BE A SUPER PITA

I HAVE A MICS WITH 4.1XC ATTACHED IS A NAM 4.0.04. I NEED TO USE PORTS 13 AND 14 TO ADD TWO MORE 0X16s. I AM TOLD THE 7.1XC SOFTWARE WILL ENABLE THEM, BUT THEN MY NAM WILL NEED TO BE REPLACED. DOES THE 7.0XC ALSO SUPPORT PORTS 13 AND 14 ON THE EXPANSION, AND AM I CORRECT THAT THE 4.0 NAM IS...

THanks

I CURRENTLY HAVE A MICS WITH 4.1XC SOFTWARE GETTING READY TO UPGRADE TO 7.1XC. I WANT TO MAKE SURE THE NAM IS RUNNING 4.1 AND NOT 4.0.

I HAVE A MICS WITH 2 PRI, 2 6 PORT FIBER EXPANSION, 9 0X16 MODULES, AND 1 ANALOG STATION MODULE. I RECENTLY ATTACHED 2 MORE 0X16S TO THE PORTS 13 AND 14 OF THE EXPANSION CARD. THE PROBLEM IS THAT THE MODULES DONT SEEM TO INITIALIZE, IF A HANDSET IS ATTACHED IT JUST FLASHES BUT IT NEVER COMES UP...

I HAVE A 0X32 WITH DIDs SETUP FOR EACH EXTENSION. DURING NORMAL RINGING MODE THE DIDs RING CORRECT INTO THE PROGRAMMED EXTENSION. HOWEVER IN NIGHT RINGING ALL DIDs ARE PICKED UP BY THE AUTO ATTENDANT INSTEAD OF RINGING AT THE PROGRAMMED EXTENSION. ANY SUGGESTIONS?

YOU KNOW I HAVEN'T IT WOULD BE VERY ODD IT IF IT WAS DISABLED BUT HEY STANGER THINGS HAVE HAPPENED

TRIED IT. IT WILL NOT IF BOTH T1 CARDS ARE INSTALLED. BUT IT WILL COME UP IN EITHER SLOT IF ONLY ONE CARD IS INSTALLED...I THOUGHT IT WAS WEIRD TOO

YEP. IT SEES BOTH CARDS UNDER HARDWARE BOTHE ARE SET FOR PRI AND I VERIFIED THE FRAMING WITH THE PROVIDER. IS IT POSSIBLE THAT 4.1 DOES NOT SUPPORT MULTIPLE PRI

I HAVE AN OLDER MICS RUNNING 4.1 I BELIEVE. WE ARE TRYING TO ADD A SECOND PRI TO THE SYSTEM BUT THE CARD JUST FLASHES LIKE IT IS NOT SYNCING I SWAPPED THE CARDS THINKING ONE MIGHT HAVE BEEN BAD..BUT IT WORKS. I HAVE ALREADY TURNED UP THE SERVICE SO I KNOW IT IS NOT A CROSS CONNECT OR PROVIDER...

FORGOT TO MENTION IM USING AN MICS WITH OLD 4.1 SOFTWARE

THANKS FOR THE CHART