Search results for query: *

Thanks PERRYPJ that was the clue I needed - saved me a lot of time - all fixed now I was able to get into PM and re-record the all the prompts - can't thank you enough you are indeed the wisest of phone world Owls!!!!!!!http://picturehosting.com/images/nabisho/img0488.jpg

I don't know how to get to prompt maintenance, I see it on the list of voice services but how do I access it? http://picturehosting.com/images/nabisho/img0615.jpg

I've got a Meridian 11e with a Meridian Mail module and I need to change the greetings/selections (like press 1 for accounting etc.)on the main incoming voice tree, where do I do that at, is it in the Merdian Mail system somewhere?

It's RCMD CA11 23C (aka Richmond Main) this was shot with an early betamax camera by one of the switchman the day before they cutover of the No. 1 xbar machine, not a lot of live video of running crossbar machines around, but you can sure hear that old clicking/rattle racket on this one. Nothing...

The data/lan/ethernet connection was a separate link using a couple transcievers from BlackBox and an 8 port SMC switch at the new plant end. The phone mux had it's own single mode pair just for the line extensions. The mux we bought extended both the analog and digital lines over to the new...

I used one of these to line muxes to extend 12 Meridian 11c lines analog lines and 2 Meridan digital lines to a remote plant we built about 7 years ago. We trenched in single-mode fiber and I used one pair for the line extender/mux and another for the data/lan connections. So far it has worked...

Here's some old video from back in the 80's that was shot of #1 xbar and #5 xbar machines that I worked in back in the 70's. The #1 is a full 20 - 20 #1 xbar(40K lines) and the #5 is a #5 xbar with 20 K lines. There's also some footage of an old #12 LTD with analog meters. Thought some of the...

Worked in a few of those over the years - was a switchman on a cutover of a 33,000 line stepper in Fresno back in about '79-'80 those were some impressive machines during a busy hour. I'm still working on the video clip of the crossbar machine hope to get it up today or tomorrow - stay tuned if...

Verizon said they tested everything and it all looked OK, they came out and replaced a board in the NIU/Loopback box and 10 minutes later everything magically cleared and the B-Channel card went all green. I enabled all my B's one at a time and we are now 100% golden again except for a couple...

Well I saw Verizon go into the circuit now is all channels show "disabled" instead of MBSY - looks they are at least looking at the right circuit now - if they will just enable it and take the make busy off I think we'll be back - on knees praying now. NAB :-)

Still no inbound or outbound on the ISDN Pri all channels 01 thru 23 show: CH ## - MBSY DID VOD * Ch 24 3DCH Looks like the d-channel is up OK, but all the B channels are all made busy somewhere - I tried all the disables and enables on the loop - no help. Verizon called they say the circuit...

OK we're up and running - got the config to restore and everything is up inside - still can't get anything inbound because I think the ISDN Pri is locked out somewhow inside Verizon, my 4 backup dial tones are letting me get calls out again but nothing working i9nbound from Verizon - I'm off to...

Well we're up and shipping dialtone again - but I can't log in regarless of what i do i get "TTY 00 SCH MTC BUG so I can't get to LD 143 to restore our database NAB :-)

That was it! I was putting in all the packages and all I had to do was tell it 22 packages - we're loading now it looks like it's going to come up - thanks all i'll give everyone a final update when we back in service :-) NAB :-)

Well if I take the default list of additional packages when I get to the final "is this correct" it shows Additional Packages: None. I've tried just answering yes to everything - still shows none, if I type in all the packages manually it takes them all but when I reach "is this correct" only...

That might be it - when I choose Enterprise I didn't tell it 22 additional packages - I'm off to try it again - I'll let you know NAB :-)

no go - could it be because I don't have the original flash card that came with the release and I'm trying to use a 22.16 flash card I got aftermarket? This card will let me restore my data from the Z drive but it looks like it won't take my keycodes. NAB :-)

Here's my numbers 775-783-9355 or by cell 775-790-2314 NAB :-)

Yes the name of the company is Bently if that's the car you're talking about that's our name. We don't make cars though we make pressurized bearings. If you have the codes please call me I'm desparete I can't get this switch and the 200 lines back in service until I can re-load the OS. NAB :-)