Recent content by TOVERBO

What did you do to resolve your problem ? In the same boat here. Have a ton of duplicates. We usually make one phone the main and make another a phantom # and monitor the main line - down fall is when your on the phantom phone to answer a call to the main # you have to pick up the handset and...

I was able to sift through a few of the other messages and figured it out. I did an unaquire of my cdn in ld 23. Out my cdn Then created my new cdn - make sure cntl is set to yes Then changed the dial in # in call pilot call wizzard. Then reboot the cp server to aquire the new cdn on the 81c.

Would like to change my cp cdn from 1000 to 1004 on my 81c. Could someone lend me a hand in doing this?

One last follow up - you can use NI2 - it appears to work but does not - drops calls after 1 ring. Confirmed with another person who had also created a link between the nortel 81 and shoretel. Not sure if that means all nortel. Also when the shoretel people clicked an clid check box in their...

Everything went well. The Enet card went into my slot 86 the 720c card went into 13-14. I had one cable to connect enet and t1. I had another to my msdl card 15 port 1 on net 0. Another cable went from the t1 card which I needed a db15 to rj45 to connect to the shoretel t1 box. I used loop 86...

I have a clock in core0 and core1 each is already set up for dch0 and backup dch0. Where does the clock come from for this t1. Does it pull from the system already by a setting - external or does it have to come from the shoretel side - anyone?

So pri2 means dual pri card? Well shoretel will be here monday with the demo system for 30 days. I will post the results. Thanks for the correspondence. It's been awesome.

Did a little more diggin and found in some docs that with tmdi - it said isgf and with the msdl they had it to isig. The other thing that I see is on dgtp they put pri on tmdi and pri2 on msdl. Same way when they program the channels. Is that setting specific to the type of t1 card you use? I...

The only other difference I saw on the doc is they use tmdi and I am going to use msdl - They use ISGF - I have also seen ISIG - I have packages QSIG (263, 305, 316) or NI-2 (291, 385). Should I use one or the other?

Ok, good. On the dch messages questionI did a dis msgi 13(dch#)in ld 96 to get rid of the dch messages. I was reading some info and you can do qsig and ni-2 with an option 11 to shore gear - I would think it would be the same. There just wasn't any new info on starting at cequ step by step...

Sorry - let me try to clear this up. There was a post above: are you putting a dch on it?? that will require that you dis and enl the msdl card, otherwise, build your T-1 and your trunks and enll in ld 60 So in my response there was a type - o . It should have read: I have a primary dch 0...

Any thought on the dch question? Another question about the DCH. I am programing a dchannel (13). I have a primary dch 0 on msdl 15 on port 0 and a back up DCH 1 on msdl 15 port 0. If I am going to use port 1 on the msdl should I choose the back up to disable so I don't disrupt service when...

I should have posted the new look of my cequ after deleting 86 and putting it back in as pri2 CEQU MPED 8D TERM REMO TERD REMD TERQ 019 033 REMQ SUPL 004 008 020 024 036 040 052 056 068 N152 V156 SUPC SUPF 048 XCT 014 030 046 062 064 080 TDS...

I should have posted the new look of my cequ after deleting 86 and putting it back in as pri2 CEQU MPED 8D TERM REMO TERD REMD TERQ 019 033 REMQ SUPL 004 008 020 024 036 040 052 056 068 N152 V156 SUPC SUPF 048 XCT 014 030 046 062 064 080 TDS...

USA - So your thinking to piggy back the Shoretel I need to have it programed in CEQU as PRI2 and not PRI? It must get all the framing off the shoretel system? There are no options for ESF or any of that when doing PRI2. Another question about the DCH. I am programing a dchannel (13). I have...