Installing T1 link for Shortel 1

[TOVERBO]

I am trying to install a t1 card 720C. I did get some documentation on programing the card from shoretel.
I just have a few questions if anyone can help. I have an open net shelf in net 2 that I would like to populate.
I know it is slot specific and that is my problem. I have slots 6-14 open on Net 2 shelf 1. I believe the tie would be 80 something.
Do I need to have the enet card installed also. Can I put both in the same shelf.
I have worked with t1 cards already installed just never set one up on my own.
I did get some information from previous posts also. Any help would be appreciated.

 

[TOVERBO]

The system is an 81c on 4.5 - forgot to post

 

[TOVERBO]

cequ print out

CEQU
MPED 8D
TERM
REMO
TERD
REMD
TERQ 019 033
REMQ
SUPL 004 008 020 024
036 040 052 056
068 N152 V156
SUPC
SUPF 048
XCT 014 030 046 062
064 080
TDS * 014 * 030 * 046 * 062
* 064 * 080
CONF * 015 028 * 031 * 047
060 * 063 * 065 * 081
MFSD * 014 * 030 * 046 * 062
* 064 * 080

DLOP NUM DCH FRM TMDI LCMT YALM TRSH
TRK 000 24 D4 NO AMI DG2 00
001 24 ESF NO B8S FDL 00
002 24 ESF NO B8S FDL 00
016 24 ESF NO B8S DG2 00
018 24 ESF NO B8S FDL 00
035 24 ESF NO B8S FDL 00
PRI 003 24 ESF NO B8S DG2 00
032 24 ESF NO B8S DG2 00
034 24 ESF NO B8S DG2 00
044 24 ESF NO B8S FDL 00
045 24 ESF NO B8S FDL 00
MISP
EXT0 3PE
CNI 012 000 000
CNI 012 001 001
CNI 013 000 002
EXT1 3PE
CNI 012 000 000
CNI 012 001 001
CNI 013 000 002
MCFN S0B0 S0B1 S1B0 S1B1 S2B0 S2B1 S3B0 S3B1 FLSH TOTL
016 000 016 000 016 016 016 016 64 160

 

[phonz1]

A 720 cards require an enet card, that would be cabled to the 720, I would try to keep the 720 out of the network shelf or move it as far to the right as possible.

 

[TOVERBO]

How does the system know when you program the card to what slot your using?
I was thinking of putting it in slot 13-14

 

[Jeffnortel]

You will have to place a QPC414 card into the network slot you program. Looks as if loop 0 or 3 are the most obvious choice. Place the 720 card in a slot that will not block network space if you can, it only needs power.

 

[TOVERBO]

I have the loop installed and everything is looking good. Thanks to all who shared.
One question is . is there a way to print out the specs or your loop other than a cequ print out?

 

[Jeffnortel]

thats really about it, other than printing the channel's in LD 20(TNB), the dchannel in LD 22 (if PRI), lastly the rout in LD 21

these are a bit obvious just figured i would mention

 

[TOVERBO]

when intalling the t1 is there a sequence of installing the enet card and cabeling to the 720c card.
Do you insert the enet then the 720c and then connect all the cable?

 

[phonz1]

no real sequence... install the enet with the faceplate disabled, install the 720 and the cables... are you putting a dch on it?? that will require that you dis and enl the msdl card, otherwise, build your T-1 and your trunks and enll in ld 60

 

[TOVERBO]

One last question.
When I first programmed the t1 I installed it as a pri and it had 24 channels. I was told to program as pri2 and when I print out that comes up with 31 channels.
Setting up qsig t1 for shoretel system.
Are pri 2 31 channels - just wondering if that sounds right?
I don't have the system piggy backed yet and it looks like it is functioning fine so far.

 

[phonz1]

PRI2 or NI2?? what country are you in?

 

[TOVERBO]

USA -
So your thinking to piggy back the Shoretel I need to have it programed in CEQU as PRI2 and not PRI?
It must get all the framing off the shoretel system? There are no options for ESF or any of that when doing PRI2.
Another question about the DCH. I am programing a dchannel (13). I have a primary dch 0 on msdl 15 on port 0 and a back up DCH 1 on msdl 15 port 0. If I am going to use port 1 on the msdl should I choose the back up to disable so I don't disrupt service when I disable the MSDL card ?
Also getting this message- can I shut it off.

TIM375 05:37 24/9/2008 CPU 1

DTC001


AUD000

TIM375 06:00 24/9/2008 CPU 1

DTC001


DCH: 13 MAINT INDICATION TIME: 6:03:24
COUNTER VALUE
3 255


DTC001


AUD000

TIM375 06:27 24/9/2008 CPU 1

DCH: 13 MAINT INDICATION TIME: 6:29:20
COUNTER VALUE
3 255

 

[tnphoneman]

I think you need to be ESF/B8ZS for the line coding and framing. You then need to program as NI2 protocol on the dchannel and route. PRI2 is the equivelant to an E1 that is why you have more channels.

Signature===========================================
Artificial Intelligence Is No Match for Natural Stupidity.

The latest survey shows that 3 out of 4 people make up 75% of the population.

The original point and click interface was a Smith & Wesson.

Red meat is not bad for you, it is the green fuzzy meat that is bad.

 

[TOVERBO]

I should have posted the new look of my cequ after deleting 86 and putting it back in as pri2

CEQU
MPED 8D
TERM
REMO
TERD
REMD
TERQ 019 033
REMQ
SUPL 004 008 020 024
036 040 052 056
068 N152 V156
SUPC
SUPF 048
XCT 014 030 046 062
064 080
TDS * 014 * 030 * 046 * 062
* 064 * 080
CONF * 015 028 * 031 * 047
060 * 063 * 065 * 081
MFSD * 014 * 030 * 046 * 062
* 064 * 080

DLOP NUM DCH FRM TMDI LCMT YALM TRSH
TRK 000 24 D4 NO AMI DG2 00
001 24 ESF NO B8S FDL 00
002 24 ESF NO B8S FDL 00
016 24 ESF NO B8S DG2 00
018 24 ESF NO B8S FDL 00
035 24 ESF NO B8S FDL 00
PRI 003 24 ESF NO B8S DG2 00
017 24 ESF NO B8S DG2 00
032 24 ESF NO B8S DG2 00
034 24 ESF NO B8S DG2 00
044 24 ESF NO B8S FDL 00
045 24 ESF NO B8S FDL 00
PRI2 086
DTI2
MISP
EXT0 3PE
CNI 012 000 000
CNI 012 001 001
CNI 013 000 002
EXT1 3PE
CNI 012 000 000
CNI 012 001 001
CNI 013 000 002
MCFN S0B0 S0B1 S1B0 S1B1 S2B0 S2B1 S3B0 S3B1 FLSH TOTL
016 000 016 000 016 016 016 016 64 160

rdb

ROUT 53

TYPE RDB
CUST 00
ROUT 53
DES SHORETEL
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
MODE PRA
IFC ISIG
SBN NO
PNI 00848
NCNA NO
NCRD NO
CTYP UKWN
INAC NO
ISAR NO
CPFXS YES
DAPC NO
INTC NO
DSEL VOD
PTYP DTT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 853
TCPP NO
TARG 01 02
CLEN 1
BILN NO
OABS
INST
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096

IENB 5
TFD 0
VSS 0
VGD 6


PAGE 002

DRNG NO
CDR NO
VRAT NO
MUS YES
MRT 3
RACD NO
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO

DCH 13print out

ADAN DCH 13
CTYP MSDL
GRP 1
DNUM 9
PORT 1
DES SHORETEL
USR PRI
DCHL 86
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC ISIG
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE NET
CNEG 1
RLS ID **
QCHID YES
RCAP COLP NDO
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7

 

[phonz1]

I don't think or know that in the US we'd use PRI2, I never have!

 

[TOVERBO]

I should have posted the new look of my cequ after deleting 86 and putting it back in as pri2

CEQU
MPED 8D
TERM
REMO
TERD
REMD
TERQ 019 033
REMQ
SUPL 004 008 020 024
036 040 052 056
068 N152 V156
SUPC
SUPF 048
XCT 014 030 046 062
064 080
TDS * 014 * 030 * 046 * 062
* 064 * 080
CONF * 015 028 * 031 * 047
060 * 063 * 065 * 081
MFSD * 014 * 030 * 046 * 062
* 064 * 080

DLOP NUM DCH FRM TMDI LCMT YALM TRSH
TRK 000 24 D4 NO AMI DG2 00
001 24 ESF NO B8S FDL 00
002 24 ESF NO B8S FDL 00
016 24 ESF NO B8S DG2 00
018 24 ESF NO B8S FDL 00
035 24 ESF NO B8S FDL 00
PRI 003 24 ESF NO B8S DG2 00
017 24 ESF NO B8S DG2 00
032 24 ESF NO B8S DG2 00
034 24 ESF NO B8S DG2 00
044 24 ESF NO B8S FDL 00
045 24 ESF NO B8S FDL 00
PRI2 086
DTI2
MISP
EXT0 3PE
CNI 012 000 000
CNI 012 001 001
CNI 013 000 002
EXT1 3PE
CNI 012 000 000
CNI 012 001 001
CNI 013 000 002
MCFN S0B0 S0B1 S1B0 S1B1 S2B0 S2B1 S3B0 S3B1 FLSH TOTL
016 000 016 000 016 016 016 016 64 160

rdb

ROUT 53

TYPE RDB
CUST 00
ROUT 53
DES SHORETEL
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
MODE PRA
IFC ISIG
SBN NO
PNI 00848
NCNA NO
NCRD NO
CTYP UKWN
INAC NO
ISAR NO
CPFXS YES
DAPC NO
INTC NO
DSEL VOD
PTYP DTT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 853
TCPP NO
TARG 01 02
CLEN 1
BILN NO
OABS
INST
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096

IENB 5
TFD 0
VSS 0
VGD 6


PAGE 002

DRNG NO
CDR NO
VRAT NO
MUS YES
MRT 3
RACD NO
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO

DCH 13print out

ADAN DCH 13
CTYP MSDL
GRP 1
DNUM 9
PORT 1
DES SHORETEL
USR PRI
DCHL 86
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC ISIG
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE NET
CNEG 1
RLS ID **
QCHID YES
RCAP COLP NDO
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7

 

[TOVERBO]

Any thought on the dch question?

Another question about the DCH. I am programing a dchannel (13). I have a primary dch 0 on msdl 15 on port 0 and a back up DCH 1 on msdl 15 port 0. If I am going to use port 1 on the msdl should I choose the back up to disable so I don't disrupt service when I disable the MSDL card ?
Also getting this message- can I shut it off.

TIM375 05:37 24/9/2008 CPU 1

DTC001


AUD000

TIM375 06:00 24/9/2008 CPU 1

DTC001


DCH: 13 MAINT INDICATION TIME: 6:03:24
COUNTER VALUE
3 255


DTC001


AUD000

TIM375 06:27 24/9/2008 CPU 1

DCH: 13 MAINT INDICATION TIME: 6:29:20
COUNTER VALUE
3 255

 

[phonz1]

yes, that would be what you'd want to do but you say the primary and secondary are on the card and the same port, can you clear that up?

Also, you are getting this very confusing, you have a primary dch 0 and a b/u dch 1 and are programming a new dch13?? To add a new dch wont hurt the others.... to change over to the b/u dch wont do anything for your new dch

 

[TOVERBO]

Sorry - let me try to clear this up. There was a post above:

are you putting a dch on it?? that will require that you dis and enl the msdl card, otherwise, build your T-1 and your trunks and enll in ld 60

So in my response there was a type - o . It should have read:
I have a primary dch 0 on msdl 9 on port 0 and a back up DCH 1 on msdl 15 port 0. This already exists prior.

I have now programmed a 3rd - dch13. To be used for my shoretel link to loop 86 route 53.
I am wondering if I have to disable the msdl and enable what effect will that have to my existing dchannel (depending on which msdl card I choose). If there is a disruption in service (disable/enable) - I should then put my new dch13 (port 1) on the same msdl (15) backup dch - so I don't disrupt service for this proceedure. Is this a fast proceedure? Maybe it won't be that service affecting. That is what I am wondering.
I apprecitate all your help -