Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by TeleBug27

  1. TeleBug27

    DT700 SV8100 SIP Registration

    These phone, four, have never been used on our system. Have performed a factory reset from admin/maintenance menu. the Terminal Status of the phone is as follows: Firmware version: NEC Std SIP 2.3.61.12 Terminal File Version: 1.210 Hardware Version: 9.1.4.3 SIP Information: Account name not...
  2. TeleBug27

    DT700 SV8100 SIP Registration

    We have a few DT700 handsets with SIP 2.3.61.12 Firmware Trying to get them registered on a SV8100, have factory reset the phone but not registering and the extension number is still displayed on the phone, will not clear and get extension number from SV8100
  3. TeleBug27

    6940 Phone registration

    I am trying to register a 6940 to a mivoice250 (v6.3.6.21) I have created a 69xx phone in the system and defaulted the 6940 Phone When the phone boots it is asking for a PIN, what PIN is this referring to, I assumed it was the same as registering 52xx/53xx Phones i.e. *** Extension
  4. TeleBug27

    HX Controller FPGA upgrade fail

    We have three 580.3000 826.5550R7.1 HX controller boards one has been upgraded to Version 6.1 with no issues the other two fail the FPGA upgrade
  5. TeleBug27

    Mitel SIP-DECT Base Station RFP 35 IP

    I am trying to connect a Mitel SIP-DECT Base Station RFP 35 IP to a 3CX system The 622d DECT will subscribe and appears to register to the 3CX and will get a dial tone. However when I try and dial the DECT, you get a ringing tone on the 3CX phone but the DECT wont ring
  6. TeleBug27

    DT820 SV8100

    Will a DT820 work on a SV8100? after clearing the phone, it reboots and displays incomplete config
  7. TeleBug27

    9611G SIP to H323

    Can a 9611G be converted back to H323 from SIP. Have changed the SIG from default to H323 but when it restarts its looking for 96x1Supgrage.txt not 96x1Hupgrade.txt
  8. TeleBug27

    OpenStage 15

    We have an OpenStage 15 with HFA V3 R0,23.0 Using File transfer tried to downgrade to OS_15_HFA_V2_R0_98_0.img Get error "File not supported
  9. TeleBug27

    Polycom Soundstation IP 5000 Factory Reset

    I am trying to factory reset a Soundstation IP 5000 Have tried pressing 1,3,5,7 on start-up, put the MAC address in, but does not clear the config, or reset the Advanced Menu Password
  10. TeleBug27

    Siemens HiPath OpenOffice ME ADMIN

    What is the default IP address and Login in for the OpenOffice ME ?
  11. TeleBug27

    7961G Boot

    have a few of these that are taking around 35 seconds for the display to come on after the green speaker light. other 7961G phones are about 15-20 seconds, is this normal?
  12. TeleBug27

    Cisco 2811 HTTP interface not working

    Found that the config files had a shutdown command on the fastethernet port. deleted this and reloaded configs, all working ok.
  13. TeleBug27

    Cisco 2811 HTTP interface not working

    We have a 2811 that was working ok, until we were unable to use the web manager interface. I had been working fine until then. I can ping the 2811 but if I try and access through the browser it just times out. I have defaulted it and reloaded the config files, but still the same problem.
  14. TeleBug27

    IP500v2 History

    yes
  15. TeleBug27

    IP500v2 History

    Is there a way of factory defaulting the IP500v2, i.e. licence history etc.?

Part and Inventory Search

Back
Top