Search results for query: *

These phone, four, have never been used on our system. Have performed a factory reset from admin/maintenance menu. the Terminal Status of the phone is as follows: Firmware version: NEC Std SIP 2.3.61.12 Terminal File Version: 1.210 Hardware Version: 9.1.4.3 SIP Information: Account name not...

We have a few DT700 handsets with SIP 2.3.61.12 Firmware Trying to get them registered on a SV8100, have factory reset the phone but not registering and the extension number is still displayed on the phone, will not clear and get extension number from SV8100

I am trying to register a 6940 to a mivoice250 (v6.3.6.21) I have created a 69xx phone in the system and defaulted the 6940 Phone When the phone boots it is asking for a PIN, what PIN is this referring to, I assumed it was the same as registering 52xx/53xx Phones i.e. *** Extension

We have three 580.3000 826.5550R7.1 HX controller boards one has been upgraded to Version 6.1 with no issues the other two fail the FPGA upgrade

I am trying to connect a Mitel SIP-DECT Base Station RFP 35 IP to a 3CX system The 622d DECT will subscribe and appears to register to the 3CX and will get a dial tone. However when I try and dial the DECT, you get a ringing tone on the 3CX phone but the DECT wont ring

Will a DT820 work on a SV8100? after clearing the phone, it reboots and displays incomplete config

Can a 9611G be converted back to H323 from SIP. Have changed the SIG from default to H323 but when it restarts its looking for 96x1Supgrage.txt not 96x1Hupgrade.txt

We have an OpenStage 15 with HFA V3 R0,23.0 Using File transfer tried to downgrade to OS_15_HFA_V2_R0_98_0.img Get error "File not supported

I am trying to factory reset a Soundstation IP 5000 Have tried pressing 1,3,5,7 on start-up, put the MAC address in, but does not clear the config, or reset the Advanced Menu Password

What is the default IP address and Login in for the OpenOffice ME ?

have a few of these that are taking around 35 seconds for the display to come on after the green speaker light. other 7961G phones are about 15-20 seconds, is this normal?

Found that the config files had a shutdown command on the fastethernet port. deleted this and reloaded configs, all working ok.

We have a 2811 that was working ok, until we were unable to use the web manager interface. I had been working fine until then. I can ping the 2811 but if I try and access through the browser it just times out. I have defaulted it and reloaded the config files, but still the same problem.

yes

Is there a way of factory defaulting the IP500v2, i.e. licence history etc.?

I have two 8662 phones that are in SIP mode and trying to switch back to IPT Have tried powering on the phone holding keys 5 & 6 but it just boots up to SIP

Is there any way to see if a processor expansion board is working. Other than seeing the card is listed in IP Connections?

Is there a list of handsets that would display the BT Branding?

We know that if a IP500v2 has had the branding license applied it is permanently stored in the IP500 itself and shows up as a BT logo or "BT IP Office" on some Handset displays, such as the 9508 on R8.1 or above. We have not come across any R8.0 and below to display the logo or "BT IP Office"...

have a DTIM8 which was all working fine until I went into the Web manager and changed it to dhcp (this was done in trying to get another IPECS module working) Now though it will not boot. If I monitor the serial output it gets stuck on DHCP request, although I have a DHCP running on my pc...