Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by oldtimer27

  1. oldtimer27

    Definity Remote Access command

    You mention that you have Autherization set to yes but your not entering a Autherization number. You can just enter a "n" in the remote access form and forget about the Autherization number. The other thing to is make sure your COS has trunk to trunk transfer set to yes
  2. oldtimer27

    TN750C announcement alarm

    Correct you will not erase the announcements by busying out the board or the reset board command. If you physically reset the board you will loose them all. If you only have one TN750 just enter "save announcements" it will write to your memory card, to restore the announcements to the TN750...
  3. oldtimer27

    TN750C announcement alarm

    You cannot backup announcements with out circuit 17 in working order. Circuit 17 on the TN750 is a data module circuit used for saving and restoring announcements. Try and identifing the ext number of circuit 17 "list data-module", once you have the ext number try "status data-module (number)"...
  4. oldtimer27

    Resetting audix channels

    also check the option switches on the old card, and make changes on the new card if needed
  5. oldtimer27

    Alarm Display

    If you would like to verify that avaya resolved a alarm, just enter "list history" and page through to the day in question, look for MAINT port, you should be able to see what test was run to resolve the alarm.
  6. oldtimer27

    Lucent 8400B Plus Data Terminal

    sorry about that I forget what you had said earlier. We know: The CDR device is good. The PBX says the 8400 is inservice/idle.( no wiring issues to the 8400 but no data to it) This sort of points back to the processor to digital port. the processor connects to the port via PGATE-PORT on older...
  7. oldtimer27

    Lucent 8400B Plus Data Terminal

    the 513 indicates trouble with the CDR device itself or the connection to it from the 8400b. the 257 is a link retry test. can you swap the cdr devices?
  8. oldtimer27

    Lucent 8400B Plus Data Terminal

    also try "status data-module XXX" and make sure it is not busied out try "dispaly errors" and then tab down to catagory and put in cdr then "enter
  9. oldtimer27

    Lucent 8400B Plus Data Terminal

    try "release cdr secondary" if it passes check status.
  10. oldtimer27

    Lucent 8400B Plus Data Terminal

    Do you have any CDR alarms? What version G3R is it?Enter "display system-parameters cdr" and verify the secondary cdr is programed to your 8400.
  11. oldtimer27

    Lucent 8400B Plus Data Terminal

    That means your good from the board to the 8400. When you enter "status cdr" what is the condition of the secondary cdr?
  12. oldtimer27

    Lucent 8400B Plus Data Terminal

    I'm leaving for the day. Once you get the data-module number enter "status data-module XXXX" if it says disconnected its most likely a wire problem, check for continuity of the wire.
  13. oldtimer27

    Lucent 8400B Plus Data Terminal

    DOH! yes it can be a 2 wire. can you run a test data-module on it? Does it say disconnected when you status dat-module xxx?
  14. oldtimer27

    Lucent 8400B Plus Data Terminal

    It could be a wiring problem. Each 8400b is assigned a extension number and is wired to a 4 wire digital station port. Try entering "list data" and see if any data-modules are named primary, secondary cdr or cdr1, cdr2. Once you have identified the data-module extension number you can trace out...
  15. oldtimer27

    DS1 for QSIG To MM

    Avaya Configuration Note 3603 for Qsig to a Octel states a TN767 rev C or E will work. http://support.avaya.com/elmodocs2/Octel/config/cn3603.pdf

Part and Inventory Search

Back
Top