Recent content by ntcnctek

Does anyone know if there is a patch for TDS005 errors on release 5? Nortel stated that this was fixed in release 4.5 but we are now getting them on a realese 5.0 system

This is exactly what i have done although i have another system with the same release working with 7 digits and not having to go throuh the SDN table. Nortel has came back with a patch for the PBX and CP. I will try tonight to see if this fixes the issue. Patch is 21796

GIVE IVR command is telling script that you want to go to CP and give it Treatment which is followed by the App ID in CP. This is used to make the recordings for Symposium rather than using 3rd party devices.

I have a site which is forwarding their number to site B. Call lands but when it goes to the Call Pilot it states that you have been forwarded to a voice mail system however the number you dialed does not subscribe to the system. I have a SFA on the receiving end set and have the DN associated...

I have changed the settings and we are still experencing this every 15 seconds. I will open a ticket with the carrier. I have noticed that this is one of 4 T-1s and there is no traffic that hardly hits this

Good thought, i did not program this but i always program the otbf to 127. I will change and let you know if this fixes the issue.

Here is the DCH programming. I thought there is a way to turn off the MON feature in LD 96. >ld 22 PT2000 REQ prt TYPE adan dch 24 ADAN DCH 24 CTYP TMDI CARD 04 PORT 1 DES TAMPA USR PRI DCHL 4 OTBF 32 PARM RS232 DTE DRAT 64KC CLOK EXT IFC NI2 ISDN_MCNT 300...

It shows 0 on all, Isn't there a way to disable the MON in LD 96. I thought it was something like "LOG MON OFF" or TTY MON OFF .lcnt 4 PRI LOOP 4 TRSH CNT: BPV -000 SLIPD -000 SLIPR -000 CRC -000 LOSFA -000 OS_BPV -000 OS_LOSFA-000 OS_YEL -000 . DCH: 24 MAINT INDICATION TIME...

Does anyone know how to stop this message from occuring every 15 seconds? I have stated monitoring and it is showing off. DCH: 24 MAINT INDICATION TIME: 13:45:48 COUNTER VALUE 10 255

I thought that the TLAN and ELAN (talks to PBX) was used for. See below: Embedded LAN (ELAN) IP address: 167.11.58.164 Embedded LAN (ELAN) MAC address: 00:1B:BA:F0:1B:C0 Telephony LAN (TLAN) IP address: 167.11.58.227 Voice LAN (TLAN) gateway IP address: 167.11.58.225 Hostname: 125w_mc_01...

Does anyone know what the Telephony LAN (TLAN) DSP IP address is used for in the programming of the card in EM?

Does anyone know where to setuop QSIG for T1 connection from a Nortel to Avaya PBX?

NAMD is what triggers the XXXX but I am getting it when they have NAMA as you see above. I will try and out the name and rebuild if that does not work I guess I will open a case with Nortel. I will let you guys know the outcome.

They do have CLBA but that is used for blocking outgoing CLID lines. I have 2 phones and they both have the same CLS with one getting xxxx and the other getting name display. ??? this is the cls on both phones CLS CTD FBD WTA LPR MTD FNA HTA TDD HFA GRLD CRPD STSD MWA LMPN RMMD SMWD AAD...

Has anyone experience the nane display on some sets displaying xxxx instad of the name? We recently upgraded to release 5 and it only happens on a few sets even though they are programed the same as a set that works.