Recent content by mahsood

Hi all, I am starting to learn avaya PBX. The avaya site has lot of document and i am unable to understand where to starts. Can some body point me right direction. I am an experience Nortel tech and starting avaya. Or if could somebody sent me some plain documents to start learning avaya. I will...

Any more help??

Hi all, Does some body knows what will be Avaya next business plan regarding Nortel products?? Does Avaya carry/continue some nortel products like CS1000E/Microsoft OCS integration??? Thanks

Hi all, udate on this. I disconnected CISCO router (2800 series) and connected both PBX with E1 link and there is no delay. The other site CISCO router is waiting to start handshaking with Noortel PBX and vice versa. When i dial # with dial digit then there is no delay and other router start...

Hi. We are using router to use data and as well as to connect both nortel PBX using E1 card of CISCO router(2800 series router). At both site router call trace capture i get dialout number but the other site router waits 5 or 7 seconds to start communication with Nortel PBX and vice versa. I...

Hi i have tied 02 nortel PBX using CISCO router E1 connectivity. When i dial from one site to other it has 5 sec. delay to complete call. The cisco guy setup`d trace on both router. The other router sendsout digit to PBX after 5 second, I dont know whay it is waiting??? IS it waiting for more...

Here is data requested (I have also a DTI tie setup working on this site and have no dialing issue)This TIE setup is using CISCO Router with E1 card at bot sites. I dont know why pressing # makes calls OK even if i tried different FLEN, ESN ---- REQ prt CUST 0 FEAT esn MXLC 30 MXSD 30...

Here u go, I am only mentioning the required/important prompts. RLI 1 ------ ENTR=0 LTER=NO ROUTE=1 FRL=0 DMI=1-->has no insertion/deletion MFRL=0 CDP ---- DSC=4xxx FLEN=4--->i also tried different values RLI=1 Please not that with accesscode+ext# call instantly goes through but with CDP i...

Gene do u means ON/OFF duration??? It is continous tone as default and i need it to configure as of busy tone... Regards

Hi, i am using CLS LDTA on all analog extension to get disconnect tone, But it is a continuous tone like a normal tone and i need it should be like busy/disconnect tone (On/OFF), i mean fast busy type tone. Where can i set LDTA tone frequency and on which prompt??? It is 61c rls 4.5.

It is programmed as DSC, I also tried DSC=4 and DSC=4xxx (4 digit ext) with different FLEN/NCDP settings but still same. I dont know why tone heard before call gets OK. It sounds nortel PBX tone but shud it be CISCO tone also??

Hi i have 02 sites having 11c rls 5 and 61c rls 4.5 with QSIG license. I am connecting these both sites using CISCO router,Both sites CXISCO router have E1 card installed. Both Nortel PBX have set SIDE=NET/CISCO is seet as SLAVE.AT both sites TIE DCH and PRI is up and CDP are also configured...

Hi Need some help regarding length of cable connecting CISCO Router(E1 card)with 61c. What is the save length of cable connecting CISCO router with 61c. Note that we are using 61c rls 4.5/Dual to connect with it a remote site by using CISCO router E1 option.Both side have CISCO router with E1...

these 02 cages machine generic code is same???? i mean can i use license/keycode file with cage NT4N41 inspite of using NT4N40 as in Nortel QRN, or does both cages can be use same keycode file.

Sorry it was typo it is NT4N41 and Nortel recommended is NT4N40