TIE question using CISCO router

[mahsood]

Hi i have 02 sites having 11c rls 5 and 61c rls 4.5 with QSIG license. I am connecting these both sites using CISCO router,Both sites CXISCO router have E1 card installed. Both Nortel PBX have set SIDE=NET/CISCO is seet as SLAVE.AT both sites TIE DCH and PRI is up and CDP are also configured. When i dial any ext across site lets say 4XXX i get dial tone and few milisecond call goes through. I dont know why i am getting PBX tone before call getting through, DLTN=NO in ESN, I also tried FLEN settings but still get dialtone after dialing 4XXX etc..and then call goes through. WHen i dial # call instantly goes through.I checked different CDP lenth/FLEN but still gets dialtone after dialing and then call goes through. Its happening across both sites, when i dial TIE route access code and then no following # i also gets through. When i dial throug CDP i get dialtone first and then call goes through. What i am missing, i dont know. Can somebody help in this??
Regards

 

[NortelGuy1979]

So 4 is a ACOD? or an AC2, or the beginning of a DSC?

Exactly what is the digit string you are dialing; and then can you print a DNB of the first digit you dial, and then print whatever it is (IE, DSC, etc)

Thanks,
Matthew

Matthew - Technical Support Engineer

 

[mahsood]

It is programmed as DSC, I also tried DSC=4 and DSC=4xxx (4 digit ext) with different FLEN/NCDP settings but still same.
I dont know why tone heard before call gets OK. It sounds nortel PBX tone but shud it be CISCO tone also??

 

[NortelGuy1979]

Can you print the DSC and RLI and post?

Matthew - Technical Support Engineer

 

[mahsood]

Here u go, I am only mentioning the required/important prompts.


RLI 1
------
ENTR=0
LTER=NO
ROUTE=1
FRL=0
DMI=1-->has no insertion/deletion
MFRL=0

CDP
----
DSC=4xxx
FLEN=4--->i also tried different values
RLI=1

Please not that with accesscode+ext# call instantly goes through but with CDP i when i dial 4xxx i get dial one for 4 second then call goes through, however when i dial 4xxx# call instantly goes through.
On CISCO trace of both router 4xxx shows instantly as i dial but it takes time to mature call with other nortel pbx and vice vers.
Other site CDP=3xxx.

Anymore help??

 

[NortelGuy1979]

Can you print the entire ESN data block, and that entire RDB? also the entire RLI please.

Thanks,
Matthew

Matthew - Technical Support Engineer

 

[mahsood]

Here is data requested
(I have also a DTI tie setup working on this site and have
no dialing issue)This TIE setup is using CISCO Router with E1 card at bot sites. I dont know why pressing # makes calls OK even if i tried different FLEN,




ESN
----
REQ prt
CUST 0
FEAT esn

MXLC 30
MXSD 30
MXIX 30
MXDM 30
MXRL 30
MXFC 30
MXFS 30
MXSC 30
NCDP 4-->I also tried different length.
AC1
AC2
DLTN NO
ERWT YES
ERDT 6
TODS 0 00 00 23 59
RTCL DIS
NCOS 0 - 0
NCOS 1 - 1
NCOS 2 - 2
NCOS 3 - 3
NCOS 4 - 4
NCOS 5 - 5
NCOS 6 - 6
NCOS 7 - 7
NCOS 8 - 8
NCOS 9 - 9
NCOS 10 - 10
NCOS 11 - 0
NCOS 12 - 0
NCOS 13 - 0
NCOS 14 - 0
NCOS 15 - 0
NCOS 16 - 0
NCOS 17 - 0
NCOS 18 - 0
NCOS 19 - 0
NCOS 20 - 0
NCOS 21 - 0
NCOS 22 - 0
NCOS 23 - 0
NCOS 24 - 0
NCOS 25 - 0
NCOS 26 - 0
NCOS 27 - 0
NCOS 28 - 0
NCOS 29 - 0
NCOS 30 - 0
NCOS 31 - 0
NCOS 32 - 0
NCOS 33 - 0
NCOS 34 - 0
NCOS 35 - 0
NCOS 36 - 0
NCOS 37 - 0
NCOS 38 - 0
NCOS 39 - 0
NCOS 40 - 0
NCOS 41 - 0
NCOS 42 - 0
NCOS 43 - 0
NCOS 44 - 0
NCOS 45 - 0
NCOS 46 - 0
NCOS 47 - 0
NCOS 48 - 0
NCOS 49 - 0
NCOS 50 - 0
NCOS 51 - 0
NCOS 52 - 0
NCOS 53 - 0
NCOS 54 - 0
NCOS 55 - 0
NCOS 56 - 0
NCOS 57 - 0
NCOS 58 - 0
NCOS 59 - 0
NCOS 60 - 0
NCOS 61 - 0
NCOS 62 - 0
NCOS 63 - 0
NCOS 64 - 0
NCOS 65 - 0
NCOS 66 - 0
NCOS 67 - 0
NCOS 68 - 0
NCOS 69 - 0
NCOS 70 - 0
NCOS 71 - 0
NCOS 72 - 0
NCOS 73 - 0
NCOS 74 - 0
NCOS 75 - 0
NCOS 76 - 0
NCOS 77 - 0
NCOS 78 - 0
NCOS 79 - 0
NCOS 80 - 0
NCOS 81 - 0
NCOS 82 - 0
NCOS 83 - 0
NCOS 84 - 0
NCOS 85 - 0
NCOS 86 - 0
NCOS 87 - 0
NCOS 88 - 0
NCOS 89 - 0
NCOS 90 - 0
NCOS 91 - 0
NCOS 92 - 0
NCOS 93 - 0
NCOS 94 - 0
NCOS 95 - 0
NCOS 96 - 0
NCOS 97 - 0
NCOS 98 - 0
NCOS 99 - 0
ETOD
TGAR NO

RDB
----

TYPE RDB
CUST 00
ROUT 1
DES TIE
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
IDEF NET
RCLS INT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
MODE PRA
IFC ESGF
SBN NO
PNI 00000
NCNA NO
NCRD NO
CHTY BCH
CTYP UNKWN
INAC NO
ISAR NO
CPFXS YES
DAPC NO
INTC NO
DSEL VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD xxxx
TCPP NO
TARG
CLEN 26
BILN NO
OABS
INST
IDC NO
DCNO
NDNO
DEXT NO
DNAM NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952-->tried different timers
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096
IENB 5
TFD 0
VSS 0
VGD 6
DRNG NO
CDR NO
INC NO
LAST NO
QREC NO
OAL NO
CDRX NO
VRAT NO
MUS NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO


RLI
----
RLI 1
ENTR 0
LTER NO
ROUT 1
TOD 0 ON 1 ON 2 ON 3 ON
4 ON 5 ON 6 ON 7 ON
VNS NO
CNV NO
EXP NO
FRL 0
DMI 1
FCI 0
FSNI 0
SBOC NRR
IDBB DBA
IOHQ NO
OHQ NO
CBQ NO

 

[Tigernach]

I have a couple of routes that that work and I dont have any dialtone or dialing issues. The dial tone is recieved from the Cisco router in my case.

CUST 0
ROUT 1

TYPE RDB
CUST 00
ROUT 1
DES
TKTP TIE
M911P NO
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP DTI
ISDN NO
DSEL VCE
PTYP DTT
AUTO NO
DNIS NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 1801
TARG
CLEN 1
BILN NO
OABS
INST
ANTK
SIGO STD
STYP SDAT
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3

IENB 5
TFD 0
VSS 0
VGD 6
SST 5 0
NEDC ETH
FEDC ETH
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR NO
VRAT NO
MUS NO
MANO NO
EQAR NO
OHQ NO


PAGE 002

OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO

REQ PRT
TYPE:
TYPE TNB
TN 41 16
DATE
PAGE
DES
TN 041 16
TYPE TIE
CDEN SD
CUST 0
TRK DTI
PDCA 1
PCML MU
NCOS 7
RTMB 1 4
TGAR 1
SIGL EAM
STRI/STRO WNK WNK
SUPN YES
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA LPR APN THFD HKD SPCD
P10 VNL
TKID
AACR NO
DATE NO DATE

 

[trvlr1]

Could it be that the cisco router is giving you the dial tone while it is setting up the second half of the call? You might look into that and see if the programming is inserting a "pause" or "wait for dial tone" option before sending the digits to the second PBX ....

 

[mahsood]

Hi all, udate on this. I disconnected CISCO router (2800 series) and connected both PBX with E1 link and there is no delay. The other site CISCO router is waiting to start handshaking with Noortel PBX and vice versa. When i dial # with dial digit then there is no delay and other router start sending digits to nortel PBX, i tried to insert # throu DMI but it doesnt working neither it show # in DMI when i take print of DMI. Is there any possibility to insert # through DMI (as it was not showing # in print out) or is there any settings in router to insert # with every 4 digit number.
Regards

 

[johnpoole]

look at the route.dltn, provides dialtone when the route is accessed from the far end.. DLTN=NO in ESN, stops dialtone post ac only

john poole
bellsouth business
columbia,sc