Recent content by JJDiver

TTT, Thanks once again for all the help you have provided on these forums, thought about sending you another box of apples, but it's not the right time of the year (a few months before the harvest, older apples). Someone messed with the IP schema, and I used your **3 and hyperterm method to...

Good day to everyone! HX5000/MiVoice Office 250 I am looking to add four UVM port license to our existing four UVM port license. I figured enabling the additional ports would require installing a new license file. Dealer says a bit of programming is required as well. Does anyone know...

Ahh, it's a SOE Lite. Maybe the card/box isn't as old as I thought. Will check documents on Avaya. If anybody has information, I would be most appreciative. Jeff

Hello! I have a few Partner ACS I installed and the company still uses. One remote office has a Partner ACS R6, but the ACS card/box looks like an older card/box (I didn't install it.) I am wondering if Caller ID would pass to the display phones even if the ACS card/box is an older card/box...

The company I work for has FAX machines are connected to an analog extensions on a Mitel HX 5000 5.1.20. I recently discovered that when a FAX machine is receiving or sending a FAX, a second call to the same FAX number will not see a busy signal, just the normal ringing. Since the second call...

Hello, Just had a server die, data is backed up, so no worries there. Print Ques were on the server that died. Is there any chance the System State option on BUE 12.5 was backing up information needed to restore the print ques? Is there any way to recover the print ques? Tomorrow is going...

I didn't post a reply after I swapped the 308 in the first slot and a 206 in the second slot. I was abke to connect after I swapped the cards. While I don't consider this a good resolution, it did solve the problem. Jeff

I was Googling the web to see if Avaya had addressed this issue, and I found a thread I had started about the same issue on 9/5/09. I am so embarrassed. http://tek-tips.com/viewthread.cfm?qid=1562826&page=1 I didn't solve the issue back when I posted the thread, I probably just gave up and...

Thanks to Sysquest and ttech! I will try swapping the 308EC and 206 today, no spare 308's. I am able to make the swap since the site is only used for a couple months a year during cherry harvest. I had thought the 308 should be in a slot before the 206. Perhaps that only applies if you...

I was trying to connect to a Partner ACS Rel 6.85.J, same system I have connected to in past without a problem. I discovered (after much head banging) that one of my trusty, will always connect, modems had died. Grabbed another modem I had around, same model. Wouldn't connect. Checked...

Dexman, Since I was swapping the 308 and 206 I just connected to an extension. I had the same problems connecting when I was off site, calling in using an outside line. When I connect to a system, it's usually from off site. I wonder if the problems people have connecting to are not related...

Dexman, While testing lst night, I was connected to an extension on the main processor. Jeff

Jim/Dexman, I spent a few hours last night, this morning testing the system. I am able to connect if the I remove the 308 and replace with a 206. If the 308 is in the system, I can't connect. Testing results are repeatable. I also tested with just the 308 and ACS, same results, can't...

Hello! Here is a twist on an old problem--I can't connect to a Partner ACS Rel 7.91.K. This morning I swapped a 206 Rel 4.1 for a 308 (might be a 3.0.) I was able to connect without a problem before the swap, but unable to connect after the swap. System before swap, from left to right, was...

Thanks everyone for all the information. I found a ACS Rel 6 (someone on the board) that the price was way to good to pass up. I also picked up a Partner Messaging Rel 7 with four port at the same time. I support four systems, and will shuffle the Messaging Rel 7 into another location, and...