Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Recent content by janni78

  1. janni78

    ASBCE - "An encryption feature is disabled, TLS port cannot be used"

    License issue? If I remember correctly you need advance licenses for encryption (VALUE_SBCE_ADV_SESSION_1) "Trying is the first step to failure..." - Homer
  2. janni78

    Outbound Faxing

    If it's a PRI/E1 you can enable ISDN L3 Tx/Rx in trace to see why it disconnects "Trying is the first step to failure..." - Homer
  3. janni78

    Outbound Faxing

    Are you sending the 9 out on the trunk? Called Party Number = 91********* "Trying is the first step to failure..." - Homer
  4. janni78

    Getting Started with ASBCE Portwell CAD-0230 Help

    The M1 port should be on the management network, which in smaller installations is the same as internal. The A & B ports can be used for any side but think the examples use B for public and A for internal. "Trying is the first step to failure..." - Homer
  5. janni78

    Is it possible to add Workspace OVA with existing ACCS R7.1 ?

    If the ACCS is on VM Ware you install the Workspace OVA first. If it's an appliance it should install Workspace as a Hyper-V VM during upgrade. You can either install Workspace during upgrade to 7.1.1.0, or you can downgrade to 7.1.0.2 and then upgrade back to 7.1.0.3. I didn't get Workspace...
  6. janni78

    Getting Started with ASBCE Portwell CAD-0230 Help

    It should be company.com "Trying is the first step to failure..." - Homer
  7. janni78

    Is it possible to add Workspace OVA with existing ACCS R7.1 ?

    You can only add Workspace while upgrading. I was already running the latest version so I had to downgrade first to be able to add Workspace during the upgrade. Workspace also only works with LDAP accounts, so if you are currently using local accounts you need to add the server to a domain and...
  8. janni78

    TFTP updates

    There is an URL where you could get the information for each user separately, don't remember what it was now but I found it tracing on network packets from One-X Portal. Another option would be to use the Configuration Service API, it pulls the entire configuration as XML. I think the...
  9. janni78

    Time on Telephones is an HOUR OFF!!

    Didn't the old versions use Time Protocol (RFC868) and not NTP so it got the time either from Manager or VM Pro? "Trying is the first step to failure..." - Homer
  10. janni78

    Need to record twinned calls on IPOffice

    Actually you get more features with other solutions than the ones using VM Pro recordings. "Trying is the first step to failure..." - Homer
  11. janni78

    Need to record twinned calls on IPOffice

    A lot of "proper" recording solutions use packet capture :) The problem here is that the trunk comes in on the LAN2(WAN) port so that would need to be mirrored as well. "Trying is the first step to failure..." - Homer
  12. janni78

    APNs in ip office

    The root domain (111.com) doesn't need to point anywhere, Zang uses the TXT record to verify it. Normally you would have 111.com pointing at the company website, mail servers etc. "Trying is the first step to failure..." - Homer
  13. janni78

    ip office 11.0.4 softphone

    You don't need a SIP extension for Workplace, the user only needs an Office Worker or Power User license. "Trying is the first step to failure..." - Homer
  14. janni78

    Avaya 16XX phones rebooting and asking password

    I had this issue with 16xx phones on a customer when I had Phone Password set on the Extension, after removing that it worked fine. "Trying is the first step to failure..." - Homer
  15. janni78

    ASBCE with NexVortex SIP Trunk

    The IPO doesn't register to the SBC. Simply put the SBC rewrites and forwards the messages between IPO and SIP provider. You could have the SBC handle registration which is done when the PBX can't do it, but in the IPOs case it's better to have all the in the IP Office so you see if the trunk...
See more

Part and Inventory Search

Back
Top