Why I can't login in Cisco AS5300 from Console ????

[zzwjun]

AS5300????????????

1 ???????
//First problem,can't start IOS correctly

System Bootstrap, Version 12.0(2)XD1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info
AS5300 platform with 131072 Kbytes of main memory

program load complete, entry point: 0x80008000, size: 0x24effc
Self decompressing the image : #################### [OK]

%SYS-6-BOOT_MESSAGES: Messages above this line are from the boot loader.
program load complete, entry point: 0x80008000, size: 0x24effc
Self decompressing the image : ############

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706



Cisco Internetwork Operating System Software
IOS (tm) 5300 Software (C5300-BOOT-M), Version 12.3(17a), RELEASE SOFTWARE (fc2)

Technical Support:

http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Mon 12-Dec-05 16:04 by evmiller
Image text-base: 0x60008AEC, data-base: 0x6042E000

cisco AS5300 (R4K) processor (revision A.32) with 131072K/16384K bytes of memory
.
Processor board ID 27904430
R4700 CPU at 150MHz, Implementation 33, Rev 1.0, 512KB L2 Cache
X.25 software, Version 3.0.0.
Backplane revision 2
Manufacture Cookie
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x30,
Board Hardware Version 3.2, Item Number 800-2544-04,
Board Revision C32, Serial Number 28682536,
PLD/ISP Version 0.0, Manufacture Date 13-Nov-2002.
// ????????????????????IOS?????
1 Ethernet/IEEE 802.3 interface(s)
1 FastEthernet/IEEE 802.3 interface(s)
4 Serial network interface(s)
128K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
8192K bytes of processor board Boot flash (Read/Write)



Press RETURN to get started!


*Jan 17 08:35:21.275: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
*Jan 17 08:35:21.483: %SYS-5-CONFIG_I: Configured from memory by console
*Jan 17 08:35:21.483: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 5300 Software (C5300-BOOT-M), Version 12.3(17a), RELEASE SOFTWARE (fc2)

Technical Support:

http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Mon 12-Dec-05 16:04 by evmiller
*Jan 17 08:35:22.275: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0,
changed state to down
*Jan 17 08:35:22.431: %LINK-5-CHANGED: Interface FastEthernet0, changed state to
administratively down
*Jan 17 08:35:22.439: %LINK-5-CHANGED: Interface Serial0, changed state to admin
istratively down
*Jan 17 08:35:22.443: %LINK-5-CHANGED: Interface Serial1, changed state to admin
istratively down
*Jan 17 08:35:22.447: %LINK-5-CHANGED: Interface Serial2, changed state to admin
istratively down
*Jan 17 08:35:22.451: %LINK-5-CHANGED: Interface Serial3, changed state to admin
istratively down
*Jan 17 08:35:23.431: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down //???????????????
*Jan 17 08:35:23.439: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, c
hanged state to down
*Jan 17 08:35:23.443: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, c
hanged state to down
*Jan 17 08:35:23.447: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2, c
hanged state to down
*Jan 17 08:35:23.451: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3, c
hanged state to down
*Jan 17 08:35:25.447: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0,
changed state to up-
// ??????????????????
// The router stop here ,it can't go ahead anyway.


2 ??rommon>?????????
// Secondly,when entered the IOS by Ctrl-Break within 60s from begining,I can see rommon> ,but if I press any key,the mouse jump to the next row ,as showed bellow:

System Bootstrap, Version 12.0(2)XD1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info
AS5300 platform with 131072 Kbytes of main memory


monitor: command "boot" aborted due to user interrupt
rommon 1 >
//???????????Ctrl-Break???????????????????????????????rommon>???????????????????????????????????
rommon 1 > #
rommon 1 > '
rommon 1 > H
rommon 1 > H
rommon 1 >
rommon 1 >

 

[burtsbees]

What settings do you have on the console session (baud rate, stop bits, etc.). Also, do you have another rollover cable you can try, with a new rj-45 and db-9? One more thing...have you tried telnet/ssh?

Burt

 

[zzwjun]

Thank you for your reply,burtsbees! First,I'm sure that the settings I have done was correct(as:9600-8-none-1-none),the 5300 and PC were connected with a good rollover cable as you said,I think ,if the cable was bad,some IOS information couldn't show ,at last,they should be some wrong words. Secondly,I wished to login in from telnet,but the fastethernet interfaces was down(as showed above).

 

[burtsbees]

Well, it really looks like that the terminal emulator is goofing up the sent information. Have you tried to console with the exact same emulator, cable and pc to something else, successfully? Have you tried a different emulation program? Have you tried a different pc? How exactly do you know that the cable and pc and emulator are good? You must try different things to resolve your issue. If after all these things you are unsuccessful, then you can pretty much blame the asa box, unless you just want to go ahead and buy a new one without trying EVERYTHING (much less ANYTHING).

Burt

 

[zzwjun]

This problem has been solved ! The reason is that the cable I used can't receive any words in Cisco sys,not as other type of routes.I changed it for another HUAWEI cable,it's OK!

 

[burtsbees]

Hmmm...I did suggest that, and you insisted the cable was good. What cable were you using?

Burt

 

[zzwjun]

HI,Burt!Thanks! Could you tell me your MSN?
The cable I used is OK for other router but not for AS5300.

 

[burtsbees]

What is an MSN? Do you mean messenger service? I have a Yahoo one...zleppelin. The Yahoo goofnuts seem to like to try and do weird crap like "booting" and such...
It sounds like the cable still may be bad, like one pin or something. I'm not 100% on the ASA boxes as far as the console cables go, but I was under the assumption that they were the same rollover cable as the routers. Maybe it needs one more pin for data or something?

Burt