WEIRD 3300 ISSUE

[miteleh]

Here is the snapshot of a 3300 CX controller out of the box. The controller hangs at boot with the following:
MITEL SYSTEM ROM R2.0/1 Aug 24 2004 (83)

CCA Number : 56005084 RC.9 
System Model : 004f0002 F64
CPU Model : 8270 R0a10
Reset Config : 04043246
Bus Clock (MHz) : 66
CPM Clock (MHz) : 165
Core Clock (MHz) : 264
Internal Memory Map : f0000000
Main Memory (MB) : 256
Local Memory (MB) : 0
Flash Memory (MB) : 2
MAC Address : 08000f1e26d0
L2 Switch : 0
Embedded VEC : 0
POST Bypass : 0
Watchdog Bypass : 0
Slot Id : 0

Programming FPGA...

Design Name : MN3XXX_LOGIC.ncd
Xilinx Part : 2s300efg456
Build Date : 2004/07/21
Build Time : 13:09:34
Byte Count : 234456

Starting POST...

SDRAM CS1 Data Bit Walk 1................... PASSED
SDRAM CS1 Data Bit Walk 0..........
SDRAM CS2 Data Bit Walk 1................... PASSED
SDRAM CS2 Data Bit Walk 0................... PASSED
SDRAM CS1 Address Walk 1................... PASSED
SDRAM CS1 Address Walk 0................... PASSED
SDRAM CS2 Address Walk 1................... PASSED
SDRAM CS2 Address Walk 0................... PASSED
SDRAM CS1 March Test........................ PASSED
SDRAM CS2 March Test........................ PASSED

Starting vxWorks...












VxWorks System Boot


Copyright 1984-2002 Wind





CPU: Mitel Embedded PPC82XX F64
Version: VxWorks5.5.1
BSP version: 2.0/1
Creation date: Aug 24 2004, 11:37:42




Press any key to stop auto-boot...
0
auto-booting...


boot device : ata=auto
unit number : 0
processor number : 0
file name : /partition1/Rtc8260
inet on ethernet (e) : 192.168.1.2:ffffff00
host inet (h) : 192.168.1.187
gateway inet (g) : 192.168.1.251
user (u) : ftp
ftp password (pw) : ftp
flags (f) : 0x0
other (o) : motf


Disk Configuration Started.
Creating block device for controller 0 drive 0... done.
Creating CBIO device for controller 0 drive 0... done.
Attaching to partition table for 4 partitions on controller 0 drive 0... done.
Creating Cache Layer for partition 0 (/ata00) on controller 0 drive 0... done.
Creating Dos FS device for partition 0 (/ata00) on controller 0 drive 0... done.
Disk Configuration Complete.
Loading /ata00/Rtc8260...65884816
Starting at 0x10000...


Disk Configuration Started.
Creating block device for controller 0 drive 0... done.
Creating CBIO device for controller 0 drive 0... done.
Attaching to partition table for 4 partitions on controller 0 drive 0... done.
Creating Cache Layer for partition 0 (/sysro) on controller 0 drive 0... done.
Creating Cache Layer for partition 1 (/db) on controller 0 drive 0... done.
Creating Cache Layer for partition 2 (/vmail) on controller 0 drive 0... done.
Creating Dos FS device for partition 0 (/sysro) on controller 0 drive 0... done.
Creating Dos FS device for partition 1 (/db) on controller 0 drive 0... done.
Creating Dos FS device for partition 2 (/vmail) on controller 0 drive 0... done.
Disk Configuration Complete.
Attached TCP/IP interface to motfcc unit 0
Attaching interface lo0...done
Unable to add route to 192.168.1.0; errno = 0xffffffff.

Adding 114508 symbols for standalone.
/sysro/ - disk check in progress ...
dosChkLib : CLOCK_REALTIME is being reset to WED JAN 11 21:31:00 2096
Value obtained from file system volume descriptor po
The old setting was THU JAN 01 00:00:05 1970
Accepted system dates are greater than THU DEC 27 00:00:00 1990
/sysro/ - Volume is OK

total # of clusters: 400,689
# of free clusters: 327,529
# of bad clusters: 0
total free space: 1,279 Mb
max contiguous free space: 1,037,975,552 bytes
# of files: 7,341
# of folders: 350
total bytes in files: 270,845 Kb
# of lost chains: 0
total bytes in lost cha
MnLib::MnStlCachedAllocator initialized.
-> (Initialization issues if this message is seen twice.)
Last reset cause was (0x83) POWER_ON_RESET
/db/ - disk check in progress ...

/db/ - Volume is OK

total # of clusters: 1,128,571
# of free clusters: 1,117,843
# of bad clusters: 0
total free space: 17,466 Mb
max contiguous free space: 15,882,043,394 bytes
# of files: 662
# of folders: 141
total bytes in files:
# of lost chains: 0
total bytes in lost chains: 0


There is no host relink.
There is no relink on the disk.
relink_call_ctors start
relink_call_ctors done

volume descriptor ptr (pVolDesc): 0xeb35ba0
cache block I/O descriptor ptr (cbio): 0xebdb990
auto disk check on mount: DOS_CHK_REPAIR | DOS_CHK_VERB_1
max # of simultaneously open files: 82
file descriptors in use: 0
# of different files in use: 0
# of descriptors for deleted files: 0
# of obsolete descriptors: 0

current volume configuration:
- volume label: NO LABEL ; (in boot sector: )
- volume Id: 0x1dd0000
- total number of sectors: 3,211,803
- bytes per sector: 512
- # of sectors per cluster: 8
- # of reserved sectors: 32
- FAT entry size: FAT32
- # of sectors per FAT copy: 3,137
- # of FAT table copies: 2
- # of hidden sectors: 0
- first cluster is in sector # 6,306
- Update last access date for open-read-close = FALSESIGNMENT ³E : installer ³
- directory structure: VFAT
- root dir start cluster: 2
³ 13 = TRUNK C

FAT handler information:14 = NON-DIAL-IN TRUNKS
------------------------ alarm status
- allocation group size: 41 clusters
- free space on volume: 1,341,558,784 bytes³ 15 = DIAL-IN TRUNKS 16 = TRUNK

volume descriptor ptr (pVolDesc): 0xeb31e48
cache block I/O descriptor ptr (cbio): 0xebb5d38
³ 17 = HUNT GROUPS 18
auto disk check on mount: DOS_CHK_REPAIR | DOS_CHK_VERB_1
³ 19 = CALL REROUTING
max # of simultaneously open files: 82ITION ³ ³
file descriptors in use:


current volume configuration:
- volume label: NO LABEL ; (in boot sector: ) ACCESS RESTRICTION DEF ³ ³
- volume Id: 0xccd0000
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
- total number of sectors: 36,131,886ÄÄÄÄÄÄÄÄÄÄÄÄ´ ³
- bytes per sector: 512
³ ENTER FORM N
- # of sectors per cluster: 32 ³ ³
- # of reserved sectors: 32
- FAT entry size: FAT32ÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄ
- # of sectors per FAT copy: 8,822
- # of FAT table copies: 2
- directory structure: VFAT








- root dir start cluster: 2V-06

FAT handler information:LARM
------------------------
- allocation group size: 113 clusters
26 - ARS: Lea
- free space on volume: 18,314,739,718 bytes
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
/vmail/ - disk check in progress ...ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿D DIGIT TABLE


/vmail/ - Volume is OK

total # of clusters: 1,754,697
³ LEADING DIGITS ³
# of free clusters: 1,723,093UP ³IS
# of bad clu

volume descriptor ptr (pVolDesc): 0xeb2e0f0 ³
cache block I/O descriptor ptr (cbio): 0xeb35c78

³
auto disk check on mount: DOS_CHK_REPAIR | DOS_CHK_VERB_1


max # of simultaneously open files: 82ÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄ
file descriptors in use
file descriptors in use
- # of sectors per cluster: 16
- # of reserved sectors: 32
- FAT entry size: FAT32
- # of sectors per FAT copy: 13,722
- # of FAT table copies: 2
- # of hidden sectors: 0
- first cluster is in sector # 27,476
- Update last access date for open-read-close = FALSE
- directory structure: VFAT
- root dir start cluster: 2

FAT handler information:
------------------------
- allocation group size: 176 clusters
- free space on volume: 14,115,577,858 bytes

data access
Exception current instruction address: 0x0029c348
Machine Status Register: 0x0000b032
Data Access Register: 0x34000050
Condition Register: 0x80000045
Data storage interrupt Register: 0x0000b032
Task: 0xda01000 "tAppStartup"


Any ideas??? Anyone ever seen this before?? HELP!!!!!!

 

[tilf]

Looks like some form of corrupt database, try manually formatting and reloading the system software.

 

[slapin]

I would agree. Seems that hardware, at least MB,CPU and HDD are working. VxWorks is able to load a boot file. I would recomend to replace the HDD, just in case.

 

[MitelInMyBlood]

If this system is brand new out of the box, try repartitioning (details how are in the Knowledge Base on MOL) - just a minor change in the bootline tho I don't recall what it is. Once repartitioned try a manual S/W install. If the problem comes back my guess would be the drive is toast. Regardless I'd call PS in the morning and get a ticket opened on it.

 

[TheMitelGuy]

I was wondering if that KB was because of you? haha. How did you make out?

 

[MitelInMyBlood]

Wasn't for me. Perhaps you have me confused w/someone else. Knock on wood but I've never had to replace a HDD in any of my 3300s...yet anyway. I've certainly put my share of 'em in SX2Ks however.

 

[slapin]

I's a regular HDD and there is a chance that something whrong with it. I've replaced one, it died with clicking noise as any other HDD. Nightly backup is a friend of mine.

 

[CaperJ]

do you have the format process I can email also there is a new bulliten on mitel for formatting see below if you have an earlier release submit a post I will email you


Description/Symptoms
How to partition a new drive manually

Body/Solutions
As of version 6.1 UR1, you can partition a new drive manually when you install it. To do this, follow the instructions below.

Step 1
======
- Change the fields in the BootLine as shown below

boot device : motfcc
file name : Boot_Install
host inet(h) : Address of Ftp Server which holds the MN3300 software (i.e. 10.44.16.126)
other(o) : FixPartition


Step 2
======
- Reboot the system

The system will be doing the partition automatically, formatting the hard drive and installing the desired software on the box as usual.

 

[miteleh]

Wow - I dont know weather I am REALLY happy about that or REALLY scared.

It sounds like Mitel is allowing us to now partition our own drives without buying their software...... i guess we will still need the base license in AMC but i am used to being required to wait for their HDD since its pre formatted - sounds like I can use any industry standard drive now.


I like it.... but does this mean the end of the free downloads on MOL is near????

 

[CaperJ]

Yes as software assurance on the 3300 is taking affect in the new year and you need a softwware assurance subscription to upgrade or call tech support.