Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Utilizing Analog Ports?

Status
Not open for further replies.

Acoustech

Technical User
Jul 5, 2006
127
US
Inventory shows we have 8 analog ports, 5 of which are being used. I don't know that any real analog lines are being used. But I know we have 5 numbers which go to department voicemails that are type 2500. I'm assuming those are it.

-How can I check which are being counted as analog ports
-How can I set up my own personal DID (or any for that matter) to use an Analog port? (for example, i want did 555-555-7606 to become a FAX line instead of an IP phone line)
-If the above can't be done, how do we get analog lines going through the PBX at all?

Thank you
 
2500s are analogue. Out the ipset & build it back as a 500 on an analogue card.

Mato' Was'aka
 
Try printing in ld 20 at the type prompt put 500 and leave the tn prompt blank. This will show you what is programmed.
 
I am only asking this question to make sure I understand your question and Terminology, as I looked at your Profile and it looks like you are a Newbie.

"Inventory shows we have 8 analog ports, 5 of which are being used"

Where did you get this inventory and what do you mean by ports, do you mean 500 set TN's? or do you mean trunks from the Telco that go to Vmail?

I think you are asking how do you hookup a Fax machine with a DID number to the system.




This is a Signature and not part of the answer, it appears on every reply.

This is an Analogy so don't take it personally as some have.

Why change the engine if all you need is to change the spark plugs.


 
Hi. I got the printout from ld 22 REQ slt. It says Analogue Telephones 8, left 3, used 5. It's interesting cause I'm sure we're not using any analog telephones, but I think someone was right in saying 2500 is considered "analogue." Ace, you're correct that I just want to hookup a fax machine with a DID number to the system.
 
The program the DID as the DN on one of your open analog (500 or 2500) and cross connect your TN to the jack. Plug in your fax and you should be good to go.


Perfection is expected, Excellence is Tolerated
 
go to LD 81 REQ=cnt enter through until FEAT and type in sets it will tell you if they are 2500 or 500
 
Also make sure you have an analog line card in the pbx without this it doesnt matter if you have licenses or not.
 
Thanks A12. Happen to know what the tag would be on that card? (ie TDMI, MC-32, etc)
 
NT8D09 is the card part number.

Signature===========================================
Artificial Intelligence Is No Match for Natural Stupidity.

The latest survey shows that 3 out of 4 people make up 75% of the population.

The original point and click interface was a Smith & Wesson.

Red meat is not bad for you, it is the green fuzzy meat that is bad.
 
Thanks all. I see I have the card and will be trying to get this working. I appreciate the help.
 
Do
REQ luu
TYPE 500

This will list out the TN's that are available to use




This is a Signature and not part of the answer, it appears on every reply.

This is an Analogy so don't take it personally as some have.

Why change the engine if all you need is to change the spark plugs.


 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top