US IP 500

[Pepp77]

Does anyone know if the Avaya IP Office 500 will accept a 208v power supply in the US?

Normal domestic feed is 120V however a lot of IT equipment looks like it will also take 208v, especially if it has a universal power supply. I am trying to find a document to support this.

Any help would be appreciated.

| ACSS SME |

 

[Bas1234]

Here you go;


General
IP412 and all Expansion Modules
Width 445mm/17.5"
Height 71mm/2.8"
Depth 245mm/9.7"
Dimensions
IP500
Width 445mmm/17.5"
Height 73mm/2.9"
Depth 365mm/14.4"

The recommended minimum clearance, front and rear, for the connection of cables and other devices is 75mm/3".
Busy Hour Call Complete (BHCC) is a measure used to test IP Office systems under a high call load.
For BHCC tests, each incoming call rings for 5 seconds, is answered and stays connected for
Call Capacity 6 seconds. The BHCC figures for the different IP Office control units are listed below. Note that
in some cases the BHCC figure achievable will be limited by the number of incoming trunks supported.
IP500 & IP500V2 = 36000.
IP412 = 36000.
Environmental • 0°C to +40°C (32°F to 104°F): 95% relative humidity, non-condensing.
Note that the above numbers are for reference only. For practical purposes, for example the calculation of heat
dissipation, it is recommended to base environmental requirements (for example air cooling or UPS ratings) on
the maximum input rating of the power supplies of the planned IP Office configuration, as follows.
In order to calculate the maximum, that is worst case, amount of heat that can be generated by an IP Office
system, it is assumed that all input power is converted to heat; whether from the PSU itself, the system unit,
expansion module and/or cabling.
Heat dissipation is normally measured in British Thermal Units (BTU's). A heat value expressed in Watts can be
converted to BTU/hr by multiplying by 3.41297. As indicated above, you should use the maximum power input
Heat Dissipation of 115 VA of each power supply to calculate this most accurately.
Using the conversion factor:
• Heat Dissipation = 115 x 3.41297 = 392.5 BTU/hour.
The metric equivalent to BTU is a Joule where 1 BTU = 1,055 Joules.
This calculates the BTU value per power supply. The maximum BTU per system is therefore calculated, based
on total number of power supplies installed in the system. For example, for a IP412, this would be 1 for the
base unit and up to 12 for the expansion modules.
• IP412 Maximum Heat Dissipation = 13 x 392.5 = 5,103 BTU/hr.
Remember to budget for the power requirements of any additional devices that are to be co-located with the
IP Office such as server PC's (voicemail, etc).
Unit Weight IP500 System Unit - 3.2Kg/7.0lbs
IP412 Control Unit - 3.0Kg/6.7lbs
Analog 16 Module - 2.9Kg/6.5lbs
DS16 Module - 3.0Kg/6.7lbs
DS30 Module - 3.5Kg/7.8lbs
WAN3 Module - 2.8Kg/6.3lbs
So8 Module - 2.8Kg/6.3lbs
Phone 8 Module - 2.8Kg/6.3lbs
Phone 16 Module - 2.9Kg/6.5lbs
Phone 30 Module - 3.1Kg/6.94lbs
• 2.5mm DC inlet socket: 24Vdc Power input. Rating - 24Vd.c., 2A max.
Unit: 406 V1/V2 412 IPO500 ATM16 DS16 DS30 WAN3 So8 Phone8 Phone16 Phone30
16 17.5 NA 5 24 30 12 24 12 16 30
• Input
• IP406 V2, IP412 and expansion modules: 2.5mm DC inlet socket. 24Vdc power input. Rating 24V DC, 2A maximum.
• IP Office 500 System Unit: IEC AC inlet socket. 100-240V AC, 50/60Hz, 81-115VA, 2.5A maximum.
• Power Supply Units: All CE/UL/Dentori Safety Approved.

• Standard 40W Power Supply Unit (All control and expansion units unless otherwise indicated)
Supplied with the control or expansion unit. 40W PSU with integral lead to the unit. Connection to switched mains supply
requires separately supplied country specific IEC 60320 C7 power cord (2-wire figure 8 connector).
• Input: 100-240V AC, 50/60Hz, 81-115VA, 2A maximum.
Power Supply Consumption • Output: 24Vdc, 1.875A, output power 45W maximum.
(Nominal Watts) • Small Office 45W Power Supply Unit
Supplied with the unit. 45W PSU with integral lead to control unit. Connection to switched mains supply requires separately
supplied country specific IEC 60320 C13 power cord (3-wire earthed cold kettle lead).
• Input: 100-240V AC, 50/60Hz, 81-115VA, 1.5A maximum.
• Output: 24V DC, 1.875A, output power 45W maximum.
• IP406 V2 60W Power Supply Unit
Supplied with the control or expansion unit. 60W PSU with integral lead to the unit. Connection to switched mains supply
requires separately supplied country specific IEC 60320 C13 power cord (3-wire earthed cold kettle lead).
• Input: 100-240V AC, 50/60Hz, 81-115VA, 2.5A maximum.
• Output: 24V DC, 1.5A, output power 60W maximum.
• IP Office 500 80W internal Power Supply
Integral to the System Unit. Connection to switched mains supply requires separately supplied country specific IEC 60320
C13 power cord (3-wire earthed cold kettle lead).
• Input: 100-240V AC, 50/60Hz, 81-115VA, 2.5A maximum.
BTU/Hour Conversion Unit: 406 V1/V2 412 IP500 ATM16 DS16 DS30 WAN3 So8 Phone8 Phone16 Phone30
54.6 59.73 NA 17.7 81.91 102.4 40.95 81.91 40.95 54.6 102.4
· Small Office 45W Power Supply Unit
Supplied with the unit. 45W PSU with integral lead to control unit. Connection to switched mains
supply requires separately supplied country specific IEC 60320 C13 power cord (3-wire earthed
cold kettle lead).
• Input: 100-240Vac, 50/60Hz, 81-115VA, 1.5A maximum.
• Output: 24Vdc, 1.875A, output power 45W maximum.
· IP403, 406 V1 & 412 - 40W Non-Earthed Supply Unit:
•Input: 100-240Vac, 50/60Hz, 81-115VA, 2A maximum.
Power Supply Unit • Output: 24Vdc, 1.875A, output power 45W maximum.
· IP406 V2, DS 16/30V2 and Phone 8/16/30V2 - 60W Earthed Power Supply Unit
Supplied with the control or expansion unit. 60W PSU with integral lead to the unit. Connection to
switched mains supply requires separately supplied country specific IEC 60320 C13 power cord
(3-wire earthed cold kettle lead).
• Input: 100-240V AC, 50/60Hz, 81-115VA, 2.5A maximum.
• Output: 24V DC, 1.5A, output power 60W maximum
· IP Office 500 80W internal Power Supply
Integral to the System Unit. Connection to switched mains supply requires separately supplied
country specific IEC 60320 C13 power cord (3-wire earthed cold kettle lead).
• Input: 100-240V AC, 50/60Hz, 81-115VA, 2.5A maximum.

___________________________________________
It works! Now if only I could remember what I did...

Dain Bramaged (Avaya Search tool

http://tinyurl.com/bas1234

)
______________________________________