Tie trunk inserting 104 and can't figure out why 1

[khaman]

Hello,

I have a CS1K 7.0 tie trunked to a CS1K 7.5. When calling from the 7.0 site to 7.5, watching d-channel monitoring, it is inserting 104 in front of all my calls and I can't figure out why. I have checked the CDP to RLB with no DMI table inserting digits. I checked the route and there isn't anything for the INST prompt. I took a look at ESN and only using AC1, which is 9 for outside access. What am I missing? I"m sure it is something simple.

 

[KCFLHRC]

It could be a Zone Dialing Prefix

LD 117
prt zdp

 

[khaman]

I checke the zone dialing and there isn't anything setup for that. 2 zones and they are both disabled and blank for config.

 

[KCFLHRC]

So are these digital and analog phones calling from the 7.0 site to the 7.5 site via CDP and you are seeing 104 xxxx on the d-channel messaging at the 7.5 site?

 

[khaman]

That is exactly it.

I'm running into an issue with about 5% of the calls getting over to the 7.5 site and it doesn't drop the 104 and then get a recording saying "You have reached an unassigned number". Thinking that if I drop the 104 I'll get rid of the issue.

 

[KCFLHRC]

Look at the HLOC in LD 90

 

[KCFLHRC]

Or the LOC in LD 90

 

[khaman]

Nothing for teh HLOC or LOC in LD 90.

 

[KCFLHRC]

Do this

>ld 90
ESN000

MEM AVAIL: (U/P): 32628787 USED U P: 5367301 155077 TOT: 38151165
DISK SPACE NEEDED: 232 KBYTES
REQ prt
CUST 0
FEAT net
TRAN sum

 

[khaman]

This is what showed up.

REQ prt
CUST 0
FEAT net
TRAN sum



NETWORK TRANSLATION TABLES (SUMMARY)


NETWORK TRANSLATOR 1
AC1 9

TRANSLATION CODES

LOC 0
NPA 797
NXX 50
SPN 5
HNPA 0
HLOC 0
NSCC 0

SUPP DIGIT RESTRICTION/RECOGNITION &
INCOMING TRUNK GROUP EXCLUSION

LOC 0
NPA 1
NXX 0
SPN 0


NETWORK TRANSLATOR 2
AC2 NONE

TRANSLATION CODES

LOC 0
NPA 0
NXX 0
SPN 0
HNPA 0
HLOC 0
NSCC 0

SUPP DIGIT RESTRICTION/RECOGNITION &
INCOMING TRUNK GROUP EXCLUSION

LOC 0
NPA 0
NXX 0
SPN 0

TOTAL TRANSLATION CODES = 852

TOTAL SDR CODES = 1

 

[KCFLHRC]

Could there be an idc table on the other end

 

[BillCorv]

Check the DSEL prompt in your Route Data Block RDB on both switches. They should both be VOD or 3VCE. They need to match. VOD inserts the extra digits. If the other end is 3VCE it does not know what to do with the extra digits.

 

[khaman]

I see 104xxxx leaving both the 7.0 and 7.5 site but there is nothing in the IDC table, on either site, that matches with the DN range, or shows up as 104.
I looked over the 7.5 site and can't see where it's getting inserted.

 

[khaman]

Ha, the 7.5 site is VOD and the 7.0 site is 3VCE. Can I make that change without outing the route members? Or is this afterhours tear down and rebuild?

 

[khaman]

And which way should I go? VOD or 3VCE?

 

[KCFLHRC]

You can make the change without it affecting service.

 

[KCFLHRC]

I would use 3vce

 

[khaman]

Made the change so both routes are 3VCE and still getting the 104 inserted before the extension. What the heck......

 

[khaman]

Just in case I missed something here is the call flow, (CDP, RLB, DGT and Route prinouts) if I diall 5500, voicemail, from the 7.0 site.

MEM AVAIL: (U/P): 39949306 USED U P: 4810130 120433 TOT: 44879869
DISK SPACE NEEDED: 155 KBYTES
REQ PRT
CUST 0
FEAT CDP
TYPE DSC
DSC 55
DSC 55
FLEN 0
DSP LSC
RLI 0
NPA
NXX


MEM AVAIL: (U/P): 39949306 USED U P: 4810130 120433 TOT: 44879869
DISK SPACE NEEDED: 155 KBYTES
REQ ****
OVL000
>LD 86
ESN000

MEM AVAIL: (U/P): 39949306 USED U P: 4810130 120433 TOT: 44879869
DISK SPACE NEEDED: 155 KBYTES
REQ PRT
CUST 0
FEAT D

ESN009
FEAT RLB
RLI 0

RLI 0
ENTR 0
LTER NO
ROUT 18
TOD 0 ON 1 ON 2 ON 3 ON
4 ON 5 ON 6 ON 7 ON
VNS NO
CNV NO
EXP NO
FRL 0
DMI 0
CTBL 0
FCI 0
FSNI 0
DORG NO
SBOC NRR
IDBB DBD
IOHQ NO
OHQ NO
CBQ YES

ISET 1
NALT 5
MFRL 0
OVLL 0


MEM AVAIL: (U/P): 39949306 USED U P: 4810130 120433 TOT: 44879869
DISK SPACE NEEDED: 155 KBYTES
REQ PRT
CUST 0
FEAT DGT
DMI 0

ESN026
DMI ****
OVL000
>LD 21
PT1000

REQ: PRT
TYPE: RDB
CUST 0
ROUT 18

TYPE RDB
CUST 00
ROUT 18
DES
TKTP TIE
M911P NO
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC SL1
PNI 00001
NCNA YES
NCRD YES
TRO NO
CHTY BCH
CTYP UKWN
INAC YES
ISAR NO
DAPC NO
MBXR NO
MBXOT NPA
MBXT 0
DSEL 3VCE
PTYP DST
CNDP UKWN
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 7718
TCPP NO
PII NO
AUXP NO
TARG 01
CLEN 1
BILN NO
OABS
INST
ANTK
SIGO ESN5
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096



PAGE 002

IENB 5
TFD 0
VSS 0
VGD 6
DRNG YES
NDRI 00
CDR YES
INC YES
LAST YES
QREC NO
OAL YES
AIA NO
OAN YES
OPD NO
NATL YES
VRAT NO
MUS NO
RACD NO
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
CTBL 0
AACR NO

 

[BillCorv]

Try a call by dialing the ACOD of the route, then the number at the other end.