Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Swapped out SSC card and need to rebuilt from scratch

Status
Not open for further replies.
shawntoronto

shawntoronto

Technical User
Jun 14, 2002
142
CA
So, I've swapped my SSC card Rel 23.55 for another with SC1000 Rel 4.5

That's the only change I've made in the cabinet - I've trying to rebuild my sets, however, I keep getting ERR5112. Then it enables the card and gives me ERR5115, but the card is not enabled.

As a matter of fact, none of the card seem to be working, so it's there something that I should do?

This replacement SSC card was obviously configured differently when it was pulled from working service - I don't want to do a re-install of the software - I just want to re-config as I go along.

Suggestions?


Shawn
 
Sort by date Sort by votes
Does your 4.5 SSC do a EDD ok?. What are the ISM licences compared to your old V23.55 system. Are they different as I think they will be.

All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

If it's working, then leave it alone!.
 
Upvote 0 Downvote
Not familiar with EDD.

The ISM licences are different, but I have sufficient licenses to add sets.

As for STAT, I can stat card # 2 for example and the set that I add shows IDLE, the rest are unequipped.

The LED light on all cards are lit up RED.

Newbie I'm afraid.

:)
 
Upvote 0 Downvote
forgot to add, the line cards do not match the old configuration - i don't even know what the new configuration is - nor do I want to keep it
 
Upvote 0 Downvote
Try pulling all your IPE cards out of the cabinets then start deleting the TN's on each card. Then plug your cards back in and start rebuilding the phones

OLD ROLMEN WORKING ON NORTELS AND AVAYA
 
Upvote 0 Downvote
when i NEW in LD20 for CARDMLT,i get ERR SCH5066 "Disk record availability estimation cannot be performed. Ensure that a data dump has been executed."

Also, pulled the cards as suggested, deleted all info, reinserted the card, same problem.

Do I need to do something first?
 
Upvote 0 Downvote
>LD 43
EDD000
.EDD
EDD112
.
EDD000
.
TEMU051 Failure writing record to control Rec file
 
Upvote 0 Downvote
dongle was installed - what REQ in LD22 woudl give me the serial number to match?

I would have assume that if that was the error, I would not be able to boot up and log in?
 
Upvote 0 Downvote
Thanks

I assume I'm going to have to pull the card in order to check the dongle ID?
 
Upvote 0 Downvote
Status
Not open for further replies.

Similar threads

VRRyan
  • Locked
  • Question
Finding password to CS1000 5.5 SSC
Replies
2
Views
287
Firebird Scrambler
Firebird Scrambler
Jones03
  • Locked
  • Question
How to change out a digital line card
Replies
3
Views
149
bignose21
bignose21
jtr4580
  • Locked
  • Question
Paging Trunk from Cloud Based System to a Carehawk School System
Replies
0
Views
158
jtr4580
jtr4580
metoo86
  • Locked
  • Question
Need help audiocodes MP114
Replies
2
Views
181
metoo86
metoo86
BSmith01
  • Locked
  • Question
Nortel MerMail EC Rls 12 issue with Utility Card NT6P42AA
Replies
4
Views
161
BSmith01
BSmith01

Part and Inventory Search

Sponsor

Back
Top