"H" on caller display

[alecra]

Hi,

We have a 61c and 81c, connected via
TYPE:atvn
TRKri

Trouble is our voicemail system is off the 81c and calls coming from the 61c have a "H" in from of the caller id so the voicemail doesnt know what to do with it.
Ive changed CLS on a 500 set on the 61c to CLBD and it works fine as there is no caller ID.
Not sure why there is a H but we dont need it and would like caller id and voicemail.
Also as a side note CPND is not sent from the switch to switch either way.

Any help would be much appreciated.

Thanks

 

[cmawbey]

The "H" is a hard coded option in the X11/X21 software that indicates a Private Network Call.

In the US, this cannot be turned off. In the UK, the vendor can apply a special type of patch to turn this off. In Switzerland, Swisscom (who has rights to the Nortel source code) has written special patches to modify or change this on some of the older releases.

This "H" shows up regardless if the call is Q.SIG, or MCDN. It is applied whenever the PRI Setup messgae is received with NUMBER PLAN: PRIVATE and TYPE OF NUMBER: ESN or CDP.

 

[Firebird Scrambler]

From Release 25.15 onwards a number of Product Improvement Patches (PIs) have been built into the software. These are called PLUGINs

To List/Enable/Disable these PLUGINs use the following commands

First login to pdt. NB All commands are in lowercase

1. To list status of all PLUGINs plp (PLP)
2. To list status of individual PLUGINs plp # (PLP #) where # is the PLUGIN number 0 - 14
3. To enable PLUGIN ple # (PLE #) where # is the PLUGIN number 0 - 14
4. To disable PLUGIN pld # (PLD #) where # is the PLUGIN number 0 - 14

LIST OF PLUGINS

PLUGIN # PRS# Patch # Description
0 BV67946 Wrong Special Dial Tone with NT8D17CA CONF/TDS pack.
1 BV63269 MPLR12002 BRI B-Channels not marked MBSY, When D Channel Drops.
2 BV69389 Automatic Wake-up is turned off if INI occurs.
3 BV69237 MPLR11506 Hotline Enhancement for BASF.
4 BV19192 MPLR01862 After dialling a LSC followed by a DSC the user gets overflow tone
5 BV71211 NRGA is not workingwith Tandem Node & Digit Manipulation.
6 BV28124 MPLR02056 BCS set cannot release from call transfer to Attendant.
7 MP05648 DID with DNIS & IDC cannot call PLDN using SCLU.
8 MP05649 Not possible to CFW a set to PLDN using SCLU.
9 BV41730/40697 Wrong display if Att extends call with announcement.
10 BV42928 MPLR07615 CFW calls to NAS is intercepted to Nite Dn.
11 BV62151 MPLR11339 RAN cannot be accessed via route acod over network.
12 BV63726 MPLR08777 Mtce messages flooding TTY, TTY unusable.
13 BV71206 MCT should be output on answer from 500 set.
14 BV70355 MPLR09806 MCDN - Orig Dn in Display is preceded with "H"

I think you may need to enable plugin 14?.


All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[alecra]

Thanks for your help so far guys.
As a side note calls from the 81c to the 61c do not have a "H" and Vmail works fine, just 61c to 81c.

What load is the plugin commands used? im unfamiliar with that.

Thanks again.

 

[Firebird Scrambler]

You need to go into "pdt" I can't give out the default password.
From the command line, it's "ctrl" pdt

All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.