Power supply move for 2250 console

[uttommy]

We are having problems with a 2250 console staying lit up when it gets plugged up. We have done all that we know to do an dare stuck. We have replaced all the cables and tried different phones but with the same result. We have also reset the card with no luck. How do I go into the programming and out the TN so I can try and rebuild the TN.

Thanks,
Tommy

 

[telebub]

Print the TNs in LD 20.

REQ: PRT
TYPE: 2250
CUST: 0
TN: (hit return until it prints your 2250 TNs)

Then go to LD 12 and OUT those TNs and rebuild them on new TNs.

Are you using the correct power requirements on the console cable?

War Eagle!
Lions Baseball '09!

 

[uttommy]

As far as I know. I am a newbee at this stuff trying to learn as I go. It is gicing me an error sch0130 when trying to out these. Terminal has conflicting station type.

Thanks,
Tommy

 

[telebub]

You are in LD 12? Performing:

REQ: OUT
TYPE: 2250
TN: ll ss cc uu

Out the 1st TN and it will automatically out the 2nd TN.

War Eagle!
Lions Baseball '09!

 

[uttommy]

I am in LD 12 and it gives that error on either of the tn's.

Thanks,
Tommy

 

[telebub]

Can you post the printouts of the consoles?

War Eagle!
Lions Baseball '09!

 

[uttommy]

I have figured out how to out the TN but I have now got them to a new TN and still have nothing on the console.

Thanks,
Tommy

 

[uttommy]

POWERING TN 4-0-4-0
TN 020 1 04 05
TYPE PWR
CDEN 8D
CTYP XDLC
DATE 1 JUN 2009
POWERING TN 4-0-4-0
TN 20 1 4 6
DATE
PAGE
DES

TN 020 1 04 06
TYPE PWR
CDEN 8D
CTYP XDLC
DATE 1 JUN 2009

REQ: prt
TYPE: tnb
TN 4 0 4 0
DATE
PAGE
DES

TN 004 0 04 00
TYPE 2250
CDEN 8D
CTYP XDLC
CUST 0
SGRP 0
SETN 004 0 04 01
ANUM 02
IADN
ALPD NO
SSU
ICDR ICDD
ABAN ABDD
CPND CNDA
AADN
DNDI DNDA
DAPC DAPD
LANG 00
KEY 00 BVR
KEY 01 BIN
KEY 02 EES
KEY 03 TRC
KEY 04 ADL 358
KEY 05 PRK
KEY 06 DPD
KEY 07 DDT
KEY 08 DTM
KEY 09 DCW
KEY 10
KEY 11
KEY 12
KEY 13
KEY 14
KEY 15
KEY 16
KEY 17
KEY 18
KEY 19
DATE 27 OCT 2004

Thanks,
Tommy

 

[GHTROUT]

I suspect you have a wiring or TN issue. This document explains the TN arrangement:

http://www.ghtrout.com/ghtrout/files/2250_console_wiring_guide.pdf

[©] GHTROUT.com [⇔] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators

 

[trvlr1]

You might want to build something temporarily to test one of the consoles close to the PBX, where distance is not an issue. Make sure the problems you are experiencing are pwr/distance related and not a bad console.
Also, how many pwr TN's are you using for your set up? Now you have rebuilt the data TN's are they enabled?

 

[telebub]

How far is the console from the PBX? If it isn't too far, you don't need power TNs. If I were you I would take a console to the switchroom and hook it up right there. See if it works with just TNs 4-0-4-0 and 4-0-4-1. If it works, then add the power TNs and see if it still works properly. If it does, try extending it back to the operator desk without the power TNs. Basically troubleshoot one step at a time.

War Eagle!
Lions Baseball '09!