Opt 11 PRI

[Art Frederick]

I'm attempting to setup a PRI with a new carrier. Outbound calls work just fine but inbound calls will connect for just a split second and then drop. Below are the d-channel messages I have captured from the call. Trunks are configured as DID and PRI is set for National. Hoping someone might have some ideas.

DCH 4 UIPE_IMSG CC_SETUP_IND REF 00004011 CH 1 1 TOD 10:40:52
CALLED #:1991 NUM PLAN: E164 TON: LOCL
CALLING #:2609193060 NUM PLAN: E164 TON: NATL

DCH 4 UIPE_OMSG CC_PROCEED_REQ REF 0000C011 CH 1 1 TOD 10:40:52

DCH 4 UIPE_OMSG CC_ALERT_REQ REF 0000C011 CH 1 1 TOD 10:40:52
PROGRESS: INBAND INFO OR PATTERN IS AVAIL

DCH 4 UIPE_IMSG CC_DISC_IND REF 00004011 CH 1 1 TOD 10:40:52
CAUSE: #16 - NORMAL CALL CLEARING

DCH 4 UIPE_OMSG CC_RELEASE_REQ REF 0000C011 CH 1 1 TOD 10:40:52

DCH 4 UIPE_IMSG CC_RELEASE_CONF REF 00004011 CH 1 1 TOD 10:40:52

 

[bignose21]

Is the extension number that you are terminating to 1991, also can you post the RDB that TN 1 1 is a member of

 

[Art Frederick]

Yes, the carrier is sending digits for ext. 1991.

Here is the RDB and a trunk that is built.

REQ: prt
TYPE: rdb
CUST 0
ROUT
ACOD

TYPE RDB
CUST 00
DMOD 1
ROUT 2
DES LOCAL COT
TKTP DID
NPID_TBL_NUM 0
SAT NO
RCLS EXT
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 0
SBN NO
PNI 00001
NCNA YES
NCRD NO
CHTY BCH
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 1202
TCPP NO
PII NO
TARG 01 02 10
CLEN 1
BILN NO
OABS
INST
IDC YES
DCNO 0
NDNO 0 *
DEXT NO
DNAM NO
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
NBS 2048
NBL 4096


PAGE 002

TFD 0
DRNG NO
CDR NO
MUS NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
AACR NO

TYPE RDB
CUST 00
DMOD
ROUT 3
DES
TKTP COT
NPID_TBL_NUM 0
PRIV NO
SAT NO
RCLS EXT
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 0
SBN NO
PNI 00002
NCNA YES
NCRD NO
CHTY BCH
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
DSEL 3VCE
PTYP PRI
AUTO NO
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 1203
TCPP NO


PAGE 003

PII NO
TARG 01
CLEN 1
BILN NO
OABS
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
CRD 512
NBS 2048
NBL 4096
TFD 0
LEXT 100
DRNG NO
CDR NO
MUS NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
AACR NO


REQ: end
>ld 20

PT0000
MARP NOT ACTIVATED

REQ: prt
TYPE: tnb
TN 1 3
DATE
PAGE
DES

DES
TN 001 03
TYPE DID
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 0
RTMB 2 3
B-CHANNEL SIGNALING
NITE
STRI/STRO OWK OWK
AST NO
IAPG 0
CLS UNR DTN CND WTA LPR APN THFD HKD
P10 VNL
TKID

 

[Art Frederick]

Forgot to also mention, the inbound call will ring the phone for just a split second, partial ring and then the call drops. I an call the extension internally without issue.

 

[bhassell2000]

Are you using IDC tables? Can you post your D Channel programming?

Thanks,

Buddy

Linked in Profile

http://www.linkedin.com/in/buddyhassell

 

[Art Frederick]

I do have an IDC table associated with this route, but this extension is not configured. Here is the dch programming.
ADAN DCH 4
CTYP MSDL
CARD 01
PORT 1
DES primcot
USR PRI
DCHL 1
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR
CNEG 1
RLS ID 25
RCAP COLP
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
BSERV NO

 

[janaya]

try removing COLP from the RCAP on the Dchannel. I don't know what carrier you have, but I had an issue where that caused the same problem. Removed COLP and all worked fine. It's makes absolutely no sense why it would make a difference, but it did in my case.

John Anaya
Amdocs Inc.
ACSS/ACIS - CS1000 Rls 7.5/Call Pilot 5
ACSS/ACIS - SME - IP Office 8.0
APSS/APDS - Avaya UC Services

Public Profile

http://www.linkedin.com/pub/john-anaya/25/1b9/a9b/

 

[Art Frederick]

Thanks for the suggestion, I will try that.

 

[Art Frederick]

It wouldn't allow me to remove the CLOP. Received a Swh
SIDE
CNEG
RLS
RCAP xclop

SCH0531
RCAP ****
OVL000
>err sch0531
>

SCH0531
Unable to match input with stored mnemonics. The RCAP prompt in overlay
16 has been answered NDS when QSUr QSIG GF are not accessible or with
an inappropriate interface configured
(e.g. Sl 1).
Action: Reconfigure accordingly.
Severity: Info

 

[KCFLHRC]

It's actually COLP and doubt you can remove it. Out it an rebuild it

 

[Art Frederick]

COLP is the default. It won't let me Xcolp when building it. If I select another option, it puts both in.

 

[KCFLHRC]

Don't put anything in the RCAP when you build it and see if it is there

 

[Art Frederick]

Even if I don't put anything in the at the RCAP prompt, then print when built, colp is there. Get the same sch0531 if I try to remove it.

 

[KCFLHRC]

Try making the CO Type ATT instead of STD

 

[KCFLHRC]

Also that Release ID should be blank or a * in that field. That is reserved for Nortel to Nortel

 

[vztech]

I would try changing your B-channels and route to VCE

I used to have super powers but my therapist took them away...

 

[Art Frederick]

Again, I appreciate the suggestions but still experiencing the same problem.
Changed the CO Type to ATT and removed 25 from the Rls ID, no change in call behavior.

Also tried changing route to VCE, trunk is stills set for DID. With this change I no longer get a half ring on the analog station, the call just dropped once dialed.

With either of these settings I can make an external call.

 

[kstaff22]

this message shows the disconnect from the far end---telco is sending the disconnect

DCH 4 UIPE_IMSG CC_DISC_IND REF 00004011 CH 1 1 TOD 10:40:52
CAUSE: #16 - NORMAL CALL CLEARING

 

[AvayaHE]

Try OVLR = yes
Maybe , maybe

 

[AvayaHE]

Dont see DCHannel and Clock
Is that usual ?