Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Notebook/Laptop Repair Instruction or Course?
- Thread starter mbd0722
- Start date
Good luck! As you know, most desktops are basically similar. Laptops are all different, each maker has it's own design. The only way to work on them is to go to the manufacturer's site for each one and look for manuals, you won't find a whole lot.
BlinkingLeaf
Technical User
As micker377 said, notebooks are all designed differently, I don't know any repair courses for laptops. All I can say is keeping your eyes open for one and if you do work on a notebook without a course remember that a laptop is basically a shrunk down desktop. Use common sense and you should be fine...
MaxLinux2004
Programmer
There's a book by QUE entitled "Upgrading and Repairing Laptop Computers" and is available in Amazon.com. It should help you out in some problems but not all. I have this book and it helped me a lot.
As you probably already know, the reason it's so hard to find anyone locally to work on laptops is that they are so very susceptable to ESD, electro-static discharge, and most repair facilities work on them in clean rooms.
I have taken a couple of IBM Stinkpads apart and as BlinkingLeaf said, "use common sense and you should be fine." Be very attentive to what went where as there is little room for error. Because of space limitations, even cables and wiring must go exactly where it was designed to go.
Also, look for the book mentioned MaxLinx2004 at half.com. I buy almost ALL of my books there for a fraction of what Amazon charges!
Best of luck!
DWalrus
I have taken a couple of IBM Stinkpads apart and as BlinkingLeaf said, "use common sense and you should be fine." Be very attentive to what went where as there is little room for error. Because of space limitations, even cables and wiring must go exactly where it was designed to go.
Also, look for the book mentioned MaxLinx2004 at half.com. I buy almost ALL of my books there for a fraction of what Amazon charges!
Best of luck!
DWalrus
MaxLinux2004
Programmer
I must add to what DWalrus and BlinkingLeaf had already mentioned, if you have an experience in electronics repair and stuff like that, you will be fine. Except that Notebooks and Laptops are to be treated differently. Use the right tool for the right screws(job). I've seen a technician (I don't really call him technician) using an allen key instead of a Torx screw driver. The screws are tiny if not small and a lot of them if you disassemble a complete Laptop. And always be carefull on what you are pulling.
Hey DWalrus, thanks for the tip on half.com.
Hey DWalrus, thanks for the tip on half.com.
the one i use is pretty good
its on ebay,
its on ebay,
![[infinity]](/data/assets/smilies/infinity.gif "[infinity] [infinity]")
BlinkingLeaf
Technical User
mbd0722,
Go to they have a book that you might be able to use. ISBN: 0-7897-2800-1 Upgrading and Repairing Laptops.
I happened to find a listing for it in an A+ course book, didn't know if you were still looking for something like it but decided that I would let you know anyway.
Anyway, hope everything works out for you.
-Leaf
Go to they have a book that you might be able to use. ISBN: 0-7897-2800-1 Upgrading and Repairing Laptops.
I happened to find a listing for it in an A+ course book, didn't know if you were still looking for something like it but decided that I would let you know anyway.
Anyway, hope everything works out for you.
-Leaf
- Status
Similar threads