Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Not getting any messages on any TTYs

Status
Not open for further replies.

pestatp

Programmer
Oct 3, 2005
28
US
I have an Option 82c and for some reason we have stopped getting any messages to show up on the TTY. We get no alarms, no SCH messages, no any thing. All we get is the intra cont and the interloop test messages from the midnight routines.

Right before this started happening we had a fan go out in one of the groups and it was flooding error codes into the system nonstop for about an hour. Then after that, there was nothing else.
 
I forgot to mention if I try to look up an error code by doing the err err0250, it doesn't output anything for that either.
 
Go into LD 37
stat TTY
reenable the disabled TTY for that port
 
I have already tried disabling and enabling all of the ttys. That doesn't seem to be the problem.

I can still go in and make changes and whatever, its just that none of the ttys will output any messages.
 
Its not just one tty, it is all of them, to include two PTYs and straight off the core.
 
Have you checked the configuration, LD 22,
PRT
TYPE (ADAN)
to see if the TTY has those options turned on ?
USER (MTC) (SCH) (BUG) ect.
 
Example;
>LD 22

PT2000

REQ PRT

TYPE ADAN


ADAN HIST
SIZE 20000
USER MTC SCH BUG
ADAN TTY 0
TTY_TYPE SDI
CAB 00
CARD 00
PORT 0
DES SEB
FLOW NO
USER MTC SCH BUG
TTYLOG 0
BANR NO
ADAN TTY 1
TTY_TYPE SDI
CAB 00
CARD 00
PORT 1
DES VT-520
BPS 2400
BITL 8
STOP 1
PARY NONE
FLOW NO
USER MTC SCH
TTYLOG 0
BANR NO
 
Yes, all the messages are turned on. I was getting them all before and we didn't do any changes, they just stopped after we started getting all of the errors from the fan alarm.
 
how can you check tty's if they are all dead, or config..

I N I cross your fingers 1st

john poole
bellsouth business
columbia,sc
 
They aren't dead, I am just not recieving any of the user messages. I can still use all of the ttys.

And I was going to use ini as the last resort, I work on a Marine Corps base and they get a little upset if the phones are down. So I was hoping that maybe someone has seen this before and they knew another way to fix it.
 
Is your system swapping processors every night?
If yes, I would INI the system, Of course this depends on what your allowed to do, if not, I would be contacting a Vendor/Nortel ETAS
 
Check in LD 22 PARM settings ERRM see below. ERR, BUG and AUD should appear next to prompt ERRM.

REQ prt
TYPE parm

PARM
LPIB 1000
HPIB 1000
500B 500
SL1B 160
NCR 2000
MGCR NULL
CSQI 250
CSQO 250
TUBO NO
CFWS NO
PCML MU
ALRM YES
ERRM ERR BUG AUD
 
I think I just found out what the problem is. Our cmdu on the inactive side is oos. The HDD failed and it didn't tell us, even though when you stat the health in 135 it says they are redundant, they aren't. They haven't been switching at night.

So I called in a ticket. But thanks everyone for your ideas.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top