Nortel Release 23 help

[ddickenson]

I need to add a network group to my aging Option 81c that's running release 23. I have to do this in order to get enough IPE shelves to get rid of the SL-1 PE shelve's i'm currently running! In any case I've found a great NTP on adding a network group to an IGS system but it's for newer releases (Specifically whenever they added the CUTOVR command in ld 135. The first time I did this it went well and I was able to split the cores using the SPLIT command, as opposed to putting the cpu in maint mode, and go into LD17 to add the CONF/TDS and CNI cards needed. I have two groups currently (0,1) and I'll be adding group 2. Here's what I get when I try to add the CNI port

EXT0 3pe
CNI 13 0 2
CNI
EXT1 3pe
CNI 13 0 2
SCH5805


SCH5805 states that there is already a CNI port attached to group 2. When I print my CEQU, however, both EXT0 and EXT1 show the same entries for groups one and two under each heading. Also, it tells you in the NTP to split, and do these steps on core 1, then CUTOVR and do them on core 0. I can't "CUTOVR" so I haven't made it that far but also it just won't let me put in "13 0 2" on both EXT0 and EXT1. What am I missing? Does anyone have the proper books for this on this or a close release?

 

[Firebird Scrambler]

I've just dialed into a Option 61c running V23 and get the same as you do.

>LD 22
PT2000

REQ ISS

VERSION 2311
RELEASE 23
ISSUE 47 + S/W ENHANCEMENT 1.0


REQ END
>LD 135
CCED000
.STAT CNI
cni 0 12 0: remote = group 0 ENBL
cni 0 12 1: remote = NONE

cni 1 12 0: remote = group 0 ENBL
cni 1 12 1: remote = NONE
.****
>LD 22
PT2000

REQ PRT
TYPE CEQU

CEQU
MPED 8D
TERM
REMO
TERD 017
REMD
TERQ
REMQ
SUPL 004 020 N156
SUPC
SUPF
DDCS 014
DTCS
XCT 008 030
TDS * 008 * 030
CONF * 009 * 031
MFSD * 008 * 030
APVL
DTI2
MISP 024
EXT0 3PE
CNI 012 000 000
EXT1 3PE
CNI 012 000 000
MCFN S0B0 S0B1 S1B0 S1B1 S2B0 S2B1 S3B0 S3B1 FLSH TOTL
016 000 000 000 000 000 000 000 32 048

>LD 135
CCED000
.STAT CPU
cp 0 15 PASS NORMAL ENBL

cp simm/bank stat
0 0/0 ENBL


cp 1 15 PASS NORMAL STDBY

cp simm/bank stat
1 0/0 ENBL
.

Whats the status of your CPU's?.

All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[ddickenson]

Here's my CPU stat

>ld 135
CCED000
.stat cpu
cp 0 15 PASS NORMAL ENBL

cp simm/bank stat
0 0/0 ENBL
0 1/0 ENBL


cp 1 15 PASS NORMAL STDBY

cp simm/bank stat
1 0/0 ENBL
1 1/0 ENBL

And here's what I have when I print cequ

CEQU
MPED 8D
TERM
REMO
TERD 026
REMD
TERQ 000 001 002 003
004 005 006 007
008 009 010 011
016 017 018 019
020 021 022 023
024 025 027
REMQ
SUPL 040 044 052 056
060
XCT 012 028 034 048
064 080
TDS * 012 * 028 * 034 * 048
* 064 * 080
CONF * 013 * 029 * 035 * 049
* 065 * 081
MFSD * 012 * 028 * 034 * 048
* 064 * 080

DLOP NUM DCH FRM TRSH
TRK 014 24 ESF B8S FDL 00
015 24 ESF B8S FDL 00
030 24 ESF B8S FDL 00
031 24 ESF B8S FDL 00
036 24 ESF B8S FDL 00
EXT0 3PE
CNI 012 000 000
CNI 012 001 001
EXT1 3PE
CNI 012 000 000
CNI 012 001 001
MCFN S0B0 S0B1 S1B0 S1B1 S2B0 S2B1 S3B0 S3B1 FLSH TOTL
016 000 016 000 000 000 000 000 32 064

And finally here's what happens when I try to add the new CNI port.

>ld 17
CFN000
MEM AVAIL: (U/P): 2941796 USED: 990363 TOT: 3932159
DISK SPACE NEEDED: 444 KBYTES
2MB BACKUP DISKETTE(S) NEEDED: 1 (PROJECTED)
DCH AVAIL: 64 USED: 0 TOT: 64
AML AVAIL: 15 USED: 1 TOT: 16
REQ chg
TYPE cequ
MPED
TERM
REMO
TERD
REMD
TERQ
REMQ
XCT
TDS
CONF
MFSD
DLOP
EXT0 3pe
CNI 13 0 2
CNI
EXT1 3pe
CNI 13 0 2

SCH5805
CNI


As noted above in my CEQU printout both EXT0 and EXT1 have the same things for the two current network groups so why won't it let me add it on EXT1 if I already have on EXT0? (it also works the same reversed ie. Add to EXT1 and then try to add to EXT0 still get SCH5805

 

[bdmcdonald99]

13 is not a valid value for CNI.
CNI s p g
s = slot 9-12
p = port 0-1
g - group 0-7

Try to program with correct values and you should be fine.

It's a phone system, NOT a clock!