NARS 10 digit local dialing question. 1

[fataldata]

I'm trying to figure out how this local 10 digit call (3033372500)is routed. From a LD80 entc trace on my set I believe I am taking Route 1. I have no NPA, NXX, SPN, HNPA, HLOC, LOC under AC1 (9) for 303. I do have an NPA for 1303 that is pointed at RLI 1 which has a DMI of 0, but DMI 0 does not exist. And an SPN 3 with and FLEN 0 pointed at RLI 0. Does anyone have any suggestions, any help is greatly appreciated? Below are various printouts.

 TN 020 1 01 03
KEY 0  SCR MARP ACTIVE  TN 020 1 01 03  VGW
 TN 000   V
ORIG  020 1 01 03  0  SCR MARP  0  5905  3904
[COLOR=#EF2929]TERM  019 21  DID  RMBR  1 21[/color]
DIAL DN [COLOR=#EF2929]93033372500[/color]
MAIN_PM  DIAL    AUX_PM  COMPLETE
TALKSLOT  ORIG  73   TERM  23
EES_DATA:
NONE
QUEU  NONE
CALL ID 0 8922
AUX  NARS

I do not have entries in for 303 in NPA, SPN or NXX but do have a 1303 entry in NPA that points to RLI 1.

REQ  prt
CUST 0
FEAT net
TRAN ac1
TYPE spn
[COLOR=#EF2929]SPN  303[/color]
ESN073

REQ  prt
CUST 0
FEAT net
TRAN ac1
TYPE spn

[COLOR=#EF2929]SPN  3[/color]

SPN  3
FLEN 0
RLI  0
SDRR NONE
ITEI NONE

REQ  prt
CUST 0
FEAT net
TRAN ac1
TYPE nxx
[COLOR=#EF2929]NXX  303
ESN073[/color]

REQ  prt
CUST 0
FEAT net
TRAN ac1
[COLOR=#EF2929]TYPE npa
NPA  303
ESN073
NPA  1303

NPA  1303[/color]
RLI  1
DENY 5751235
DENY 960
DENY 976
SDRR DENY CODES = 3
ITEI NONE

DMI for RLI 1 is 0 and there is not DMI 0 only a DMI 1 which just inserts a 9 (i'll have to look at why this is setup)

REQ  prt
CUST 0
FEAT rlb
RLI  1

RLI  1
ENTR 0
LTER NO
ROUT 0
TOD  0 ON  1 ON  2 ON  3 ON
     4 ON  5 ON  6 ON  7 ON
VNS  NO
CNV  NO
EXP  NO
FRL  2
DMI  0
FCI  0
FSNI 0
SBOC NRR
IDBB DBA
IOHQ NO
OHQ  NO
CBQ  YES

ENTR 1
LTER NO
ROUT 1
TOD  0 ON  1 ON  2 ON  3 ON
     4 ON  5 ON  6 ON  7 ON
VNS  NO
CNV  NO
EXP  NO
FRL  2
DMI  0
FCI  0
FSNI 0
SBOC NRR
IDBB DBA
IOHQ NO
OHQ  NO
CBQ  YES

ISET 2
NALT 5
MFRL 0
OVLL 0

 

[StanleySteamer]

Since you have SPN 3 then that's what it will use. So RLI 0.

BTW - if you trac the TN using the DEV switch you will get details about the RLI etc.
.trac 020 1 01 03 DEV

You would have to trac it while it's being dialed but before it is answered.

 

[fataldata]

Thank you. So the FLEN of 0 matches infinite (not infinite but up till some digit limit) characters? TRAC with DEV does indicate RLI 0 entry 1.

.trac 20 1 1 3 dev

 TN 020 1 01 03
KEY 0  SCR MARP ACTIVE  TN 020 1 01 03  VGW
 TN 000   V
ORIG  020 1 01 03  0  SCR MARP  0  X905  3904
TERM  019 21  DID  RMBR  1 21
DIAL DN 93033372500
MAIN_PM  DIAL    AUX_PM  COMPLETE
TALKSLOT  ORIG  81   TERM  11
EES_DATA:
NONE
QUEU  NONE
CALL ID 0 6968

COS_ORIG    CTD       COS_TER    UNR
TGAR_ORIG    10       TGAR_TER     0
NCOS_ORIG     3       NCOS_TER     0
EXP_ROUTE   NO

AUX  NARS
DIAL DN 93033372500
NARS_PM OUTPULSE
[COLOR=#EF2929][b]RL_IND    0     RL_ENT    1[/b][/color]
DG_MAN    0     FCA INDEX   0      TOD  0


----  ISDN PRA CALL (TERM) ----
CALL REF # =  31560
BEARER CAP =  VOICE
HLC =
CALL STATE =  1     INIT
CALLING NO =  303xxxx905  NUM_PLAN:E164    TON:NATIONAL  ESN:NPA
CALLED NO  =  3033372500  NUM_PLAN:E164    TON:NATIONAL  ESN:NPA
PDCA  1  PAD  0   6   PCML MU  MU

 

[fataldata]

NVM found this to answer my FLEN length question.

[URL unfurl="true"]http://pbxbook.com/meridian/install/mer_spn.html[/url]

 

[KCFLHRC]

They call that "Short BARS", that could come back to bite you later.

 

[fataldata]

Yea this system has ton's of these kind's of things. Plenty of administered trunks, sets etc.. that are not in use.

 

[KCFLHRC]

We went to 10 digit dialing here in Kansas City several years ago. But before that you could have local 7 digit dialing within 2 different area codes. You talk about a nightmare. But 10 digit dialing eased that pain somewhat. Good luck to you.

 

[Trason806]

DMI 0 means dont chg anything. I didn't know this in the beginning and made a whole new one... that didn't chg anything.