Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
MICS PRI Outbound calls
- Thread starter covcom
- Start date
Are they on a maintenance program ? I would start by getting the Vendor of the PRI involved. Their csu for the PRI may be bad or the C.O. may have some promblem.If that checks out then I would start by swapping out the DTI card and the Cat 5 cable connecting the PRI.If that doesn't work I would then swap out the power supply on the Mics and then the cabinet and so forth. That's a tough one to trouble shoot.
First, check the 'Network' log under maint. Alarm 75's and Evt 330-337 are typically phone company dropping you and then the DS1 syncing up again. If you catch it when it's first down, check the smart jack......that may tell you something ( phone company guy in SAC 2 blocks away tracing wires and yours happens to be loose, .....). Typically, you don't have to reboot the whole system, disabling and re-enabling the card in s/w (maint)is enough. Everything has a threshold and when the DTI card gets overwhelmed with errors, it won't auto-restore. While you may have a problem with on-site eq, keep this in mind: the phone company has 3x-15x the equipment that you do to go bad (repeaters, smartjack, DSX wiring, digital card, potentially miles of cable, Lightspan eq,......). Just check/replace all connections on your side of the smartjack.
- Thread starter
- #4
- Thread starter
- #6
I replaced the DTI card and patch cord, The customer has since had to reboot the system. The local telco (embarq) installed the MICS and the PRI. They no longer have a maintence contract. It's been my account for about 3 years.
When Embarq came out and checked there side about 6 months ago, they said everything was ok, they told the customer they needed to upgrade the software. Would you try this?
I have not checked the clocking. How do I check? I may instruct the customer on how to disable the card. This is a medical facility and they reboot before I get there. No alarms have been diplayed.
Thanks again
When Embarq came out and checked there side about 6 months ago, they said everything was ok, they told the customer they needed to upgrade the software. Would you try this?
I have not checked the clocking. How do I check? I may instruct the customer on how to disable the card. This is a medical facility and they reboot before I get there. No alarms have been diplayed.
Thanks again
RikRodgers
Vendor
I would upgrade the sw. Make sure you take them to at least 6.1MR. I usually just go to 7.1.
- Thread starter
- #8
You're fine going from 5.0 to 6.1. All programming will be maintained. Going to 7.1 you'd need to make a pit stop at 6.1 first.
Brian Cox
Brian Cox
- Thread starter
- #10
RikRodgers
Vendor
I know others will disagree, but I've had pretty good success with 5.0 and PRI.
You're right- to get past that, you'll have to upgrade the NAM.
You're right- to get past that, you'll have to upgrade the NAM.
- Thread starter
- #13
- Thread starter
- #14
curlycord
Programmer
You will first need to get the PRI key code regenrated via KRS system at Nortel if you 1. opt instead to do a re-install the programming (which may clear any bugs) or 2. when swapping the cabinet.
=----(((((((((()----=
curlycord
=----(((((((((()----=
curlycord
I'm going through the same thing! I replaced the KSU, T-1 card, service card, smart jack & patch cord. 2nd MICS w/ 5.1 software. Paetec & Qwest, the "carrier" have done intrusive testing and say the circuit are good on thier side. Qwest sent a guy 2 days ago to the site. He tested the NIU, smart jack & patch cord and says everything on thier side is good and that it's the CPE equipment!
On the system I have the CSU turned on, clocking set to Primary, NI-2, ESF-B8ZS. Thier are a few other settings, which I'm not sure what they do, If someone out there has some feedback would be great.;
On the system I have the CSU turned on, clocking set to Primary, NI-2, ESF-B8ZS. Thier are a few other settings, which I'm not sure what they do, If someone out there has some feedback would be great.;
curlycord
Programmer
RikRodgers
Vendor
If that doesn't do it for you, upgrade their sw.
Ductape. I believe we have a solution. It's worked for our setup anyway . . . 3 weeks with no complaints from the customer.
Hopefully your setup is the same. Ours is a MICS with a PRI connected to a 5ESS switch at the C.O.
This link shows someone else with the same setup and symptoms I had and what was needed to fix it. (having the C.O. turn off b-channel services on the PRI)
Hopefully QWEST has the 5ESS switch and can make this change for you.
Good luck.
Hopefully your setup is the same. Ours is a MICS with a PRI connected to a 5ESS switch at the C.O.
This link shows someone else with the same setup and symptoms I had and what was needed to fix it. (having the C.O. turn off b-channel services on the PRI)
Hopefully QWEST has the 5ESS switch and can make this change for you.
Good luck.
- Status
Similar threads
- Locked
- Question
- Locked
- Question