Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

M12X0 Expansion questions

Status
Not open for further replies.

28416909

IS-IT--Management
May 20, 2003
39
US
I just install a M12X0 expansion with 2 trunk cards. I have it all wired into the 8x24, and the KSU SEES the 8 lines. How do i use the lines though? I tried activating lines 9-12 but they say "not in service" when i try to use them. I have the M12X0 plugged into port 3 of the expansion on the KSU. How can i use my new lines?
 
Cool, thats all set, but i can't figure out how to get them to work.

It is plugged into port 3.

This should be lines 9 - 12 right?

So i have configured the lines, and I Add them to a hand set, then when the handset tries to access the line, it says "Not in service" I am not sure what to do. This hardware works because it was setup at one time before.
 
Use port 8 and go into maintenace and disable then re-enable the card.
 
Then what set of numbers do I use? do I use 81 - 84?

 
No! Stations gor from bottom port up and lines top down....still line 009 and up!
Right now your line thinks its a station....power 12X0 down and move to port 8.

 
REMINDER: remember this post?
galfaro (Vendor) Mar 23, 2004
Your trunk module should be in port 8. What else do you have on that card? Your trunk modules start from top to bottom, station modules are from bottom to top. If port 8 is empty, put your trunk module on it.
Gabriel


DueE
 
Okay, I got them working partially but only one of my TC work. for only 4 lines are veiwed and in use. I also Got the alarm 51 - 8?
 
How do you have them punched on the block? It should be 2pr then skip 2pr.
 
Check your line type under lines programming for lines 13-16. 61-8-2 indicates the line type programmed is inappropriate or incompatible for the line connected to the port on the second card in port 8. Wrong trk cartridge? Wrong line type?

DueE
 
This is how I have them wired in.

Amphenol
Connector Line/Connection
Pair Color Port
1 Wh/Bl 201 Line 1
2 Wh/Or 202 Line 2
3 Wh/Gn 203 Line 3
4 Wh/Br 204 Line 4
5 Wh/Sl 205 Line 5
6 Rd/Bl 206 Line 6
7 Rd/Or 207 Line 7
8 Rd/Gn 208 Line 8
9 Rd/Br
10 Rd/Sl Emergency Telephone
11 Bk/Bl
12 Bk/Or
13 Bk/Gn
14 Bk/Br
15 Bk/Sl
16 Yl/Bl
17 Yl/Or
18 Yl/Gn Auxillary Rinig
19 Yl/Br Auxillary Rinig
20 Yl/Sl Page Control
21 Vi/Bl Page Control
22 Vi/Or Page Output
23 Vi/Gn
24 Vi/Br
25 Vi/Sl


So I am acctually soposed to skip every other pair?
 
when wiring trk cards in the mod you will punch two lines, skip 2 pair. your wiring chart is good for the first 8 lines on the KSU.

DueE
 
so it should be
Pair Color Port
1 Wh/Bl 201 Line 1
2 Wh/Or
3 Wh/Gn 202 Line 2
4 Wh/Br
5 Wh/Sl 203 Line 3
6 Rd/Bl
7 Rd/Or 204 Line 4

and so on?
 

Pair Color Port
1 Wh/Bl 801 Line 9
2 Wh/Or 802 Line 10
3 Wh/Gn 803 no connection
4 Wh/Br 804 no connection
5 Wh/Sl 805 Line 11
6 Rd/Bl 806 Line 12
7 Rd/Or 807 no connection
8 Rd/Gn 809 no connection
9 Rd/Br 810 Line 13
etc...


DueE
 
I screwed that up!! Sorry...
Pair Color Port
1 Wh/Bl 801 Line 9
2 Wh/Or 802 Line 10
3 Wh/Gn no connection
4 Wh/Br no connection
5 Wh/Sl 803 Line 11
6 Rd/Bl 804 Line 12
7 Rd/Or no connection
8 Rd/Gn no connection
9 Rd/Br 805 Line 13 (card 2/second slot)
etc...


DueE
 
Thanks a million, thats my problem, I will adjust and advise
 
28410969,
That took 35 posts to get you going. You had some very PATIENT people helping you. Hats off to everyone that stayed with it. I elected to stay out of it since you were in good hands, but that sure was a lot of reading to do.

[noevil]

MarvO said it
 
Yeah! seriously, i have been saved a HUGE ammount of time and frustration thanks to these folks. Thanks so much. This truly is a GREAT Forum! :)
 
dont forget the money aspect of this... it was all done for free

Pat Guido
NEXTIRAONE
Pat.guido@nextiraone.com

Formerly Nextira, formerly Williams Communications, formerly Wiltel, formerly Nortel networks, formerly Northern Telecom, formerly, Nynex meridian systems formerly Northern Telecom.

 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top