ITG ISDN Trunk 3.0.6 problem

[kanwalx]

Hi all, need your help as i am struggling to configure ITG ISDN trunk. I followed IP trunk guides but every time when i transmit data from OTM(TM 3.0) to ITG it gets OK but after reboot ITG TN (IPTI TN of MC32) always stays "locked out".and Dchannel always stays on AEST........after every reboot of MC32 it comes up with DISABLE channel and after disabling and then enabling again channels comes in LOCKOUT state with Dchannel on AEST.
I also replace MC32 and MSDL card and also changed IPE slot but result same. it is 61c release 4.5.
I have plugged MSDL into Slot 4 of Core 0 and its cable NTND26 one end is connected to P0 of MSDL and other end is connected to PIGTAIL cable which is then connected to Port-0 of PCMCIA inserted in MC32 . In Dchannel i have set DNUM as 13 (MSDL DIP switches are set to 13). I can easily enable/disable MSDL card....
Please guide

1- Why channels always comes up in Lockout state?? what
should i check for this problem?

2- Do i have to defile MSDL card in CEQU data?? as i
remember for ITG ISDN trunk i dont have to configure
MSDL card anywhere in CEQU data, just Dchannel
programming and DNUM setting of MSDL card.

3- Data transmit always gets OK and i can see data arriving
into MC32 when i connect CLI terminal of MC32 or Telnet
MC32. I have use two LOC code 66/67 and it was also
transmitted successfully...CLAN of MC32 is connected to
customer switch. MC32 is in slot 4-1-0 and i also tried
4-1-1.

Please help how could i avoid channels lockout and why D channel wont gets Active/establish.

Regards

 

[Triton101]

DCHIP card goes into the front slot of the MC32 and the cable goes to a external DCH Serial port (ie. MSDL).

as long as the IP side of things is setup and the CLAN connection is good, you should see it establish.

check the boot codes (LED) on the face plate and check for any FXX codes (failure codes), look those up in the guide.

I think you can check the status from the CLI of the MC32.

Also, try to do an EDD



__________________________________________________________
Find a job you love and you'll never work a day in your life. - Confucius

 

[semsem2010]

i have a same problem .
change PCMCIA card.

Samo

 

[kanwalx]

It shows LDR after boot, but the Dchannel which wont show UP and channels stays disable after boot, when i disable/enable channels got lockout and Dchannels stays AEST....Card LCD status is OK and showing LDR...
Any more help

 

[Triton101]

just to clarify, when you say enable / disable channels, you mean enable the card "ENLC x x x" correct?

did the MSDL / DCH download ok? (messages showing it's downloading) when you enabled it?

also did you set the MSDL to (RS422 DTE) on both the programming and the card?

from what I remember the IP DCH should establish even if the card is disabled, so long as the PORT on the MSDL is enabled and the DCH is enabled, should be good.


as semsem2010 suggestd, you could have bad hardware, but you should see it on the CLI of the MC32 when its booting some messages about the DCHIP errors.....etc.

do you have the IO panel filter plugged in? otherwise, the CLAN connection has to be 10 half (you have to set it)

do a basic test, plug your PC lan connection via crossover cable to the CLAN connection to the ITG trunk card and ping the CLAN ip continuously for a couple of min "ping xxx.xxx.xxx.xxx -t" to stop do "ctrl c" to cancel and then look at the arp table on your PC by typing "arp -a" and make sure the MAC address matches the CLAN IP and MAC on the MC32 (Sticker) for the CLAN.

from the MC32 CLI you can try these as well

Command Description
DCHenable
DCHdisable
DCHestablish
DCHrelease
DCHstatus



hope some of this helps.


__________________________________________________________
Find a job you love and you'll never work a day in your life. - Confucius

 

[Triton101]

oh, forgot to add, check the DCH programming to make user the USR prompt is set to NET

__________________________________________________________
Find a job you love and you'll never work a day in your life. - Confucius

 

[Firebird Scrambler]

Here are some programming details from a Option 61c V03.00 with ITG Trunks

ADAN DCH 13
CTYP MSDL
DNUM 15
PORT 1
DES itg_network
USR ISLD
ISLM 16
OTBF 32
BPS 64000
PARM RS422 DTE
CLOK EXT
NASA NO
IFC SL1
SIDE USR
CNEG 1
RLS ID 3
RCAP ND2
MBGA NO
OVLR NO
OVLS NO
T200 3
T203 10
N200 3
N201 260
K 7

TYPE TLST
TKTP TIE
ROUT 5
DES ITG_NETWORK
TN 004 1 12 00 MBER 1 ITG
TN 004 1 12 01 MBER 2 ITG
TN 004 1 12 02 MBER 3 ITG
TN 004 1 12 03 MBER 4 ITG
TN 004 1 12 04 MBER 5 ITG
TN 004 1 12 05 MBER 6 ITG
TN 004 1 12 06 MBER 7 ITG
TN 004 1 12 07 MBER 8 ITG
TN 004 1 12 08 MBER 9 ITG
TN 004 1 12 09 MBER 10 ITG
TN 004 1 12 10 MBER 11 ITG
TN 004 1 12 11 MBER 12 ITG


PAGE 002

TN 004 1 12 12 MBER 13 ITG
TN 004 1 12 13 MBER 14 ITG
TN 004 1 12 14 MBER 15 ITG
TN 004 1 12 15 MBER 16 ITG

TYPE RDB
CUST 00
ROUT 5
DES ITG_NETWORK
TKTP TIE
NPID_TBL_NUM 0
ESN NO
RPA NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
DTRK NO
ISDN YES
MODE ISLD
DCH 13
IFC SL1
PNI 00001
NCNA YES
NCRD NO
FALT NO
CTYP UKWN
INAC NO
ISAR NO
DAPC NO
PTYP ATT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 1605
TCPP NO
TARG


PAGE 007

BILN NO
OABS
INST
SIGO STD
STYP SDAT
MFC NO
ICIS YES
OGIS YES
TIMR ICF 512
OGF 512
EOD 13952
LCT 256
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GTO 896
GTI 896
SFB 3
PRPS 800
NBS 2048
NBL 4096

IENB 5
TFD 0
VSS 0
VGD 6
EESD 1024
SST 5 0
DTD NO
SCDT NO
2 DT NO
NEDC ETH
FEDC ETH
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR YES
INC YES
LAST YES
TTA YES
ABAN YES
CDRB YES
QREC NO
OAL YES
AIA YES
OAN YES
OPD YES
NDP EXC 0
CDRX NO
NATL YES
SSL
CFWR NO
IDOP NO
VRAT NO
MUS NO
PANS YES
MANO NO


PAGE 008

FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
OPR NO
ALRM NO
ART 0
PECL NO
DCTI 0
TIDY 1605 5
ATRR NO
TRRL NO
SGRP 0
AACR NO

DES ITG
TN 004 1 12 00
TYPE IPTI
CDEN 8D
CUST 0
XTRK MC32
TIMP 600
BIMP 600
AUTO_BIMP NO
TRK ANLG
NCOS 7
RTMB 5 1
CHID 1
TGAR 0
STRI/STRO WNK WNK
SUPN YES
AST NO
IAPG 0
CLS TLD DIP WTA LPR APN THFD XREP
P10 NTC
TKID
DATE 14 JUL 2005

DES ITG
TN 004 1 12 01
TYPE IPTI
CDEN 8D
CUST 0
XTRK MC32
TIMP 600
BIMP 600
AUTO_BIMP NO
TRK ANLG
NCOS 7
RTMB 5 2
CHID 2
TGAR 0
STRI/STRO WNK WNK
SUPN YES
AST NO
IAPG 0
CLS TLD DIP WTA LPR APN THFD XREP
P10 NTC
TKID
DATE 14 JUL 2005

>LD 96
.STAT DCH
DCH 013 : OPER EST ACTV DES : itg_network

I'll send you some pictures that I have taken of the cabling.

All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[kanwalx]

Here is an update...
after changing the PCMCIA for IPT DCH the dcahnnels comes up and now working OK..Thanks for every body...Can somebody mention the Eng. Code of PCMCIA which will be use with SDI/DCH card for 11c???

 

[semsem2010]

Does anyone know how to repair this card???

Samo

 

[Firebird Scrambler]

That is great news on the ITG Trunk.

Here is an Option 11c setup for you.

SDI Card configuration in slot 4

ADAN DCH 10
CTYP DCHI
CARD 04
PORT 1
DES ITG_DCH
USR ISLD
ISLM 32
OTBF 32
CLOK EXT
NASA NO
IFC SL1
SIDE USR
CNEG 1
RLS ID 3
RCAP ND2
MBGA NO
OVLR NO
OVLS NO
T23 20
T200 3
T203 10
N200 3
N201 260
K 7

>LD 21
REQ: LTM
CUST 0
ROUT
ACOD

TYPE TLST
TKTP TIE
ROUT 125
DES ITG_TRUNKS
TN 007 0 00 00 MBER 1 ITG_TRUNK
TN 007 0 00 01 MBER 2 ITG_TRUNK
TN 007 0 00 02 MBER 3 ITG_TRUNK
TN 007 0 00 03 MBER 4 ITG_TRUNK
TN 007 0 00 04 MBER 5 ITG_TRUNK
TN 007 0 00 05 MBER 6 ITG_TRUNK
TN 007 0 00 06 MBER 7 ITG_TRUNK
TN 007 0 00 07 MBER 8 ITG_TRUNK
TN 007 0 00 08 MBER 9 ITG_TRUNK
TN 007 0 00 09 MBER 10 ITG_TRUNK
TN 007 0 00 10 MBER 11 ITG_TRUNK
TN 007 0 00 11 MBER 12 ITG_TRUNK
TN 007 0 00 12 MBER 13 ITG_TRUNK
TN 007 0 00 13 MBER 14 ITG_TRUNK
TN 007 0 00 14 MBER 15 ITG_TRUNK
TN 007 0 00 15 MBER 16 ITG_TRUNK

>LD 21
REQ: PRT
TYPE: RDB
CUST 0
ROUT
ACOD

TYPE RDB
CUST 00
DMOD
ROUT 125
DES ITG_TRUNKS
TKTP TIE
NPID_TBL_NUM 0
ESN NO
RPA NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
DTRK NO
ISDN YES
MODE ISLD
DCH 10
IFC SL1
PNI 00000
NCNA YES
NCRD NO
FALT NO
CTYP UKWN
INAC NO
ISAR NO
DAPC NO
PTYP ATT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 1625
TCPP NO
TARG
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
SIGO STD
STYP SDAT
MFC NO
ICIS YES
OGIS YES
TIMR ICF 1920
OGF 1920
EOD 13952
LCT 256
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GTO 896
GTI 896
SFB 3
PRPS 800
NBS 2048
NBL 4096

IENB 5
TFD 0
VSS 0
VGD 6
EESD 1024
SST 5 0
DTD NO
SCDT NO
2 DT NO
NEDC ETH
FEDC ETH
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR NO
NATL YES
SSL
CFWR NO
IDOP NO
VRAT NO
MUS NO
PANS YES
MANO NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
OPR NO
ALRM NO
ART 0
PECL NO
DCTI 0
TIDY 7071625 125
ATRR NO
TRRL NO
SGRP 0
AACR NO

REQ


>LD 20
REQ: PRT
TYPE: TNB
TN 7
CDEN
CUST
DATE
PAGE
DES

DES ITG_TRUNK
TN 007 0 00 00
TYPE IPTI
CDEN 8D
CUST 0
XTRK MC32
TIMP 600
BIMP 600
AUTO_BIMP NO
TRK ANLG
NCOS 7
RTMB 125 1
CHID 1
TGAR 1
STRI/STRO WNK WNK
SUPN YES
AST NO
IAPG 0
CLS CTD DIP WTA LPR APN THFD XREP
P10 NTC
TKID
DATE 10 JAN 2005

DES ITG_TRUNK
TN 007 0 00 01
TYPE IPTI
CDEN 8D
CUST 0
XTRK MC32
TIMP 600
BIMP 600
AUTO_BIMP NO
TRK ANLG
NCOS 7
RTMB 125 2
CHID 2
TGAR 1
STRI/STRO WNK WNK
SUPN YES
AST NO
IAPG 0
CLS CTD DIP WTA LPR APN THFD XREP
P10 NTC
TKID
DATE 10 JAN 2005

>LD 96
.STAT DCH
DCH 010 : OPER EST ACTV AUTO DES : ITG_DCH

Regards

David


All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[kanwalx]

Can somebody knows how to repair this card?? as it is not used as storage device as other PCMCIA, i tried to read it contents but not succeeded.
Can i use same D channel PCMCIA for both 11c and 61c??? or could somebody mention exact engineering code of D channel PCMCIA for 11c?

Thanks

 

[Firebird Scrambler]

I took a search on an old Nortel parts database and found this below. I think it's the first item code you need?.

Item code = NTWE07AA Product = Pre-Programmed D-Channel Interface PCMCIA Card

Item code = NTCW84EA Product = PCMCIA D-Channel Pigtail Cable

Item code = NTRH9039 Product = H/W Assy PCMCIA Ethernet Adapter

Item code = A0683638 Product = 8MB PCMCIA Flash Card



All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[semsem2010]

item cod is NTMF93 PCMCIA Card

http://cgi.ebay.ph/NORTEL-Option11-NTMF93-Flash-Memory-Card-MC-/360268315937

Samo

 

[kanwalx]

Hi all, the Dchannel which i replaced have Eng. Code= NTWE07 and NTMF93 and it is working OK (it was at my toolbox and it is an old PCMCIA)...i got 02 other Dchannel PCMCIA card whose Engineering code are NTMF93 and NTVQxxxAE5. the faulty D channel has also Eng code NTMF93 and NTVQxxxAE5.
IS it NTVQxxx is new engineering code of D channel PCMCIA???
or is it wrong PCMCIA for IPT D channel.
Thanks

 

[kanwalx]

Hi any more help??
Still struggling with the same
the Dchannel which i replaced have Eng. Code= NTWE07 and NTMF93 and it is working OK (it was at my toolbox and it is an old PCMCIA)...i got 02 other Dchannel PCMCIA card whose Engineering code are NTMF93 and NTVQxxxAE5. the faulty D channel has also Eng code NTMF93 and NTVQxxxAE5.
IS it NTVQxxx is new engineering code of D channel PCMCIA???
or is it wrong PCMCIA for IPT D channel.
Thanks