IP Office 500 and Siemens rolm 9005

[phoneguy04]

I need some help if anyone of this problem or heard of this problem between these two switches ! Make a call from Chicagos PBX 9005 over T1 that is a tie to a router that goes to IP Office in NY . Phone rings in NY and when anwered the call on NY end disconnectes. Same happens we they call Chicago! Heres what happens on the IP office side:

Call Ref: 20 Call length: 00:00:09

Originator
Current State: Connected Time in State: 00:00:00
Currently at: Extn 4110, Main
Button Number: 1
Button Type: Call Appearance (CA)
Dialed Digits: 7228

Destination
Current State: Connected Time in State: 00:00:00
Trunk Used: Line: 17 H.323 170.137.14.1 Channel: 1
Digits sent to Central Office: 7228
Caller ID sent from Central Office:

Call target / Routing information
Short Code matched: 7XXX, Dial, System
Call Recording: No
Redirected to Twin: No
Routed across SCN trunk: No
Retargeting Count: 0

Trace Output:
6/16/08 10:21:14 AM-105ms Line = 17, Channel = 1, Q.931 Message = Connect, Call Ref = 20, Direction = To Switch
6/16/08 10:21:14 AM-110ms Call Ref = 20, Originator State = Connected, Type = User, Destination State = Connected, Type = Trunk
6/16/08 10:21:14 AM-110ms Call Ref = 20, Answered, Line = 17, Channel = 1
6/16/08 10:21:14 AM-237ms Line = 17, Channel = 1, Q.931 Message = ReleaseComplete, Call Ref = 20, Direction = To Switch, Cause Code = 65
6/16/08 10:21:14 AM-239ms Call Ref = 20, Originator State = Connected, Type = User, Destination State = Clearing, Type = Trunk
6/16/08 10:21:14 AM-239ms Call Ref = 20, Disconnect from Destination End

I have made changes on 9005 to the anwers supervision and start type and I still get the same proble ! HELP PLEASE THANKS

 

[tlpeter]

I see an code 65 wich means this:

Cause No. 65 - bearer capability not implemented.
This cause indicates that the equipment sending this cause does not support the bearer capability requested.
What it means:
1. In most cases, the number being called is not an ISDN number but an analog destination.
2. The equipment is dialing at a faster rate than the circuitry allows, for example, dialing at 64K when only 56K is supported.


ACA - Implement IP Office
ACS - Implement IP Office
ACA - Voice Services Management
______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!

 

[phoneguy04]

Thanks for the info what do you suggest I try ! I just strated to work with this IP office equipment !Thanks again

 

[mattKnight]

Cause No. 65: bearer capability not implemented.

As this is a H323 trunk I wonder if Codec mismatch/incompatability is a possibility? Evidently the signalling is OK

Take Care

Matt
I have always wished that my computer would be as easy to use as my telephone.
My wish has come true. I no longer know how to use my telephone.

 

[tlpeter]

Oke from scratch

Do you have a standard networking license ?
You need this to make iplines to work !
Can you ping the other end with system status ?
Also it is better to use "monitor" for tracing
You will think that it is a lot of info but you need to look to it
There is a lot of information in it


ACA - Implement IP Office
ACS - Implement IP Office
ACA - Voice Services Management
______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!

 

[TomMills]

just out of curiosity tlpeter, are the cause codes the same for isdn as they are for ip?

 

[mattKnight]

Whilst I never trust Wiki too much -

http://en.wikipedia.org/wiki/H.225

The h225 protocol, which is the call signalling aspect for h323 is based on Q931.

Take Care

Matt
I have always wished that my computer would be as easy to use as my telephone.
My wish has come true. I no longer know how to use my telephone.

 

[phoneguy04]

I do have network licenses and I can ping the other end! And I will give the monitor and try !

 

[tlpeter]

No not exactly the same but it is an idication


ACA - Implement IP Office
ACS - Implement IP Office
ACA - Voice Services Management
______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!

 

[phoneguy04]

Thanks for your help !

 

[phoneguy04]

We have another switch setup the same way but the other end is an IP Office 406 and that works with no problems! IP 500 is setup the same way as the 406 ! G.711 codec in NY

 

[tlpeter]

What is the codec on the Siemens ?


ACA - Implement IP Office
ACS - Implement IP Office
ACA - Voice Services Management
______________
Women and cats can do as they please and men and dogs should relax and get used to the idea!

 

[phoneguy04]

Siemens does not have a codec its an old PBX !

 

[janni78]

You should do a monitor trace so you can see what codecs it tries to set up the call with.